Blowout preventer not tested to shear pipe

The blowout preventer that failed to stop last year’s Gulf of Mexico oil spill hadn’t been tested to see if it could cut through a bent drill pipe, said a senior official of the company that made the device.

04/26/2011


The blowout preventer that failed to stop last year’s Gulf of Mexico oil spill hadn’t been tested to see if it could cut through a bent drill pipe, said a senior official of the company that made the device.

The firm hired by the government to examine the 300-ton device after they brought it up from the seafloor concluded the blind shear rams couldn’t pinch the well shut by cutting through the drill pipe. That’s because the pipe was off center. The firm faulted the design of the Cameron-made blowout preventer.

Cameron vice president David McWhorter told a federal investigative panel he couldn’t say if the company designed the device to cut through a bent drill pipe. He said it did not undergo testing for that possibility before the disaster.

“I am not going to hazard an opinion,” said McWhorter, who works in Cameron’s division that handles engineering and quality for drilling systems.

The testimony wrapped up the seventh series of hearings before the joint U.S. Coast Guard-Bureau of Ocean Energy Management Regulation and Enforcement panel, which is investigating the causes of the Deepwater Horizon rig explosion off Louisiana last April 20. The blast killed 11 workers and led to the worst offshore oil spill in U.S. history.

The panel should release a preliminary statement within the next few weeks and will issues a full report in July.

In earlier testimony, Ralph Linenberger, a BP consultant hired to monitor the blowout preventer examination on behalf of the company, questioned the findings of testing firm Det Norske Veritas. Among other things, he said he did not see evidence the drill pipe had buckled, as DNV concluded it had.

“It looked fairly straight to me,” Linenberger said.

He also said DNV did not conduct any substantive testing that would look at the possibility of maintenance of the blowout preventer being a potential factor in the device’s failure.

Transocean owned the rig that exploded and was responsible for maintaining the blowout preventer. BP was leasing the rig from Transocean and owned the undersea well that blew out.



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.