Energy harvesting: challenges for wireless monitoring applications

Energy harvesters deserve the attention they're receiving, the advent of what can be made possible through the use of ambient energy to power devices has intrigued a wide variety of technologists, developers and adopters.

06/30/2011


Potential hurdles, challenges, and requirements influence the rate of adoption of energy harvesting and sustainable energy technologies. IDTechEx technology analyst Dr. Harry Zervos recently met with Dr. Roger Hazelden, technology specialist on sensors and optoelectronics, at TRW Conekt.

Although TRW is mainly involved with components and systems for the automotive industry, the company's involvement in energy harvesting goes beyond vehicle applications. TRW research includes roadside infrastructure sensors for monitoring traffic, potential accident hazards, accidents and its effects on roads, etc. TRW's Swiss branch also is researching and developing its own thermoelectric generator.

As a supplier of tire pressure monitoring systems (TPMS), TRW uses 60-cent batteries instead of energy harvesters, which could cost several tens of Euros. According to Hazelden, cost is a major driver in applications such as TPMS's where batteries use is unregulated; a low cost coin cell will always be preferred over an expensive energy harvester. Energy harvesters would make a lot more sense in applications where there are restrictions on the use of batteries (such as aerospace), in which case they would be part of enabling technologies that would make wireless sensing/monitoring a reality.

At an energy harvesting workshop on May 4, Kenichi Soga, Professor of Civil Engineering from the University of Cambridge gave insight on the use of monitoring for structures that were built in the past with a "let's build them and see how long they last..." approach. Several of these structures are a few decades old and pose potential risks if their integrity is compromised over time. An interesting example of use of integrity sensors in a project was during some work undertaken for the London Underground, ensuring that tunnel tiles did not shift or move, leading to width changes that could be detrimental to passing trains or even fears of collapse. Again, interestingly, batteries were used for these sensors, provided by Tadiran technology. At a cost of about £40 for the battery and £200 for the whole sensor, batteries were considered, the best, most reliable option, with a lifetime of approximately 2 years, and the sensor taking measurements at a rate of 1 measurement/minute.

High costs for energy harvesters, reliability of new technologies when compared with established ones, advances in existing competing technologies (such as batteries and supercapacitors) as well as convincing potential customers of the advantages offered by new technologies as well as identifying the correct harvesting solution for the correct application tend to be recurrent challenges for the energy harvesting sensor.

It is not always easy to compete on the merits and added benefits of new devices, especially when an additional cost accompanies them. Initial costs of ownership and infrastructure necessary can add to the skepticism towards adopting innovative solutions. What tends to be important in efforts to alleviate skepticism is the use of proven solutions as examples that can convince of the real value behind the initial installation expenses. EnOcean's implementations are a great example of this and that can be seen from the large numbers of customers that have adopted the company's solutions (over 160,000 buildings are currently using EnOcean products, from wireless light switches to occupancy sensors and sensor networks for both building and industrial facilities). Such successful implementations raise the profile of energy harvesting technologies and increase awareness of potential users and the interest in finding elegant solutions to problems that cannot be solved without energy harvesting.

IDTechEx Energy Harvesting & Storage and Wireless Sensor Networks & RTLS Europe 2011 conference was held in Munich on June 21-22.

www.idtechex.com/munich IDTechEx



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.