Friction Fundamentals and Accelerating Cars

In elections, it's always the economy; in engineering, it's the fundamentals

04/01/2010


ctl1004mech_x1.jpg

Friction may well be nature's most useful phenomenon. Without it, walking would be impossible and there would be no belt drives, no clutches, no wheels and no brakes. However, in machinery in which it is not the driving force, friction is an undesirable parasitic effect, generating heat, causing wear and wasting energy. So whether the goal is to reduce friction or enhance it, the proper combination of geometry, materials and lubrication must be employed in a design, i.e., a proper tribological approach. Tribology is the study of friction and wear and it has been estimated that the correct application of tribology throughout U.S. industry could save the country $500 billion annually.

 

 

 

ctl1004mech_x2.jpg

 

We have all read about the problems with uncontrolled acceleration of automobiles due to faulty accelerator pedals. Friction has been identified as the likely culprit, and the proper combination of geometry, materials and lubrication will likely lead to a solution. Why did this happen? It is too early to answer that question with any certainty, but I do know that most engineers, including mechanical engineers, do not fully understand the friction phenomenon. Failure to understand the fundamentals of such a pervasive physical effect is bound to lead design failures, some of which might be catastrophic.

 

Stick-slip motion is a common behavior associated with friction. A typical stick-slip experiment is to attach one end of a spring to a block sitting on an unlubricated horizontal surface. The other end of the spring is moved horizontally with a constant velocity. How will the block move? Of course it is highly dependent on the physical system parameters, but one possible outcome is stick-slip motion, as shown in the figure above. When the spring force exceeds Fstick, the mass accelerates, the spring elongates and the mass comes to rest. The process then repeats, creating the stick-slip behavior. A model used to describe the friction phenomenon must be able to show this behavior. The automobile accelerator pedal relies on a balance between the return-spring force and sliding friction, which could vary over time due to wear and contamination, to perform effectively and safely.

 

In the automobile electronic accelerator pedal assembly — electronic because when the gas pedal is depressed, a sensor tells the car to accelerate — it is essential to have a certain amount of friction to make it easier for the driver to maintain a steady throttle setting and also to reduce fatigue from pushing against the pedal return spring continuously. The designed-in friction is meant to simulate the intrinsic friction that is present in a traditional throttle cable as it passes through the cable housing. If the friction is excessive, the pedal return spring cannot return the pedal when the driver's foot is removed — the pedal sticks in the partially open position. Changing the friction characteristics will of course change the accelerator feel for the driver. In addition, if wear or contamination is allowed to occur and change the friction characteristics, not only will the pedal feel change, but the safe operation may change as well. The original problem and proposed solution for a major manufacturer, Toyota, can be viewed online at www.designnews.com .

 

The Toyota pedal assembly includes a shoe that rubs against an adjoining surface during normal pedal operation. As discussed above, due to the materials used, wear, and environmental conditions, these surfaces may, over time, begin to stick and slip instead of operating smoothly. In some cases, friction could increase to a point that the pedal is slow to return to the idle position or stick, leaving the throttle partially open. A solution is to insert a spacer that will reduce the friction between the friction shoe and the adjoining surface, thus eliminating the excess friction that can cause the pedal to stick.

 

In a mechanical design, a proper tribological approach, i.e., geometry, materials and lubrication, must be taken to ensure safety, performance and energy-efficient operation.

 

 

Author Information

Kevin C. Craig, Ph.D., Robert C. Greenheck Chair in Engineering Design & Professor of Mechanical Engineering, College of Engineering, Marquette University.

 



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.