Industrial wireless or wired networks?

Tips and tricks: Have obstacles, mobile applications, or a large region? Wireless may be the best choice.

05/14/2012


Industrial wireless communication has been around for many years, perhaps first being seen in what was called “wireless MODEMs” used for communicating with remote locations where physical media like copper may not have been practical, such as remote electrical substations. Today wireless communication has become much more cost-effective, reliable, and ubiquitous, benefitting from commercial technologies like Wi-Fi, Bluetooth, and ZigBee.

When to consider wireless

Even when a wireless solution may not be the most cost-effective approach, it may be necessary because of the physical demands of the application. This may include:

Advantech’s EKI-6311GN IEEE 802.11 b/g/n wireless access point/client bridge; Courtesy: Advantech

- Physical obstacles that prevent the use of physical media like copper or fiber optic

- Mobile applications where vehicles or even palettes on an assembly line may not be easily connected to physical media

- When multiple access points are distributed over a large region: Over a wide area, wireless becomes both the most practical solution operationally, and most cost-effective. This can be anything from a large process control application to something like a monitoring system on a tank farm. In applications like this, wireless is often much less expensive for initial installation, easier to troubleshoot and maintain by qualified technicians, and able to go long distances much more cost-effectively than physical media with the cost of materials and labor to run it.

- Communication paradigms more difficult and costly to achieve with physical media systems: For example, in wireless mesh networks, sophisticated self-healing methods can be applied that significantly improve seamless recovery from a communication path disruption, and even multiple failures in the same network, increasing reliability significantly.

In an age where cell technology is dominant for consumer human communication, those same humans are trusting wireless communication to higher degrees as they design automation solutions.

- Mark Lochhaas is product sales manager, Advantech; Edited by Mark T. Hoske, content manager CFE Media, Control Engineering, Plant Engineering, and Consulting-Specifying Engineer; Reach him at mhoske@cfemedia.com.

www.advantech.com



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.