Linearity in measuring devices

10/15/2010


Dear Control Engineering: Sometimes I see the term “linearity” used in reference to measuring devices. What does this mean?

Linearity reflects the ability of a sensor to respond to changes in a measured variable in the same way across the full range. If you’ve seen old pressure gages, they often have uneven scales where the divisions are larger at one end of the scale than the other. This compensates for non-linearities in the flexing of the bourdon tube. The same concepts apply to electronic devices, whether they are process instrments such a flowmeters, or discrete devices such as proximity sensors.

Let’s use a temperature sensor as an example. It has to convert a temperature to a voltage (thermocouple) or resistance (RTD, thermistor). As the temperature changes, the voltage or resistance has to change with it. If a device has high linearity, the amount of voltage or resistance change will be the same per change in temperature across the full range of the device.

In the case of a type K thermocouple, for example, when in roughly the middle of its measuring range (500 °C) a change of 10 °C will cause a change of 0.427 mV. If the device is truly linear, that change in voltage per degree will be the same over the entire measuring range. As a matter of fact, it isn’t. At the low extreme (-250 °C) a 10 °C change is 0.017 mV. At the opposite extreme of 1,370 °C, a 10 °C change is 0.340 mV.

Thermistor resistance curve.Thermistors are generally regarded as non-linear. In an article The Challenges of Temperature Sensing, we included this graph of a typical thermistor response curve. What the graph shows is that at the low end of the range, a small change in temperature causes a large change in resistance. However the opposite is the case at the high end. The range of highest linearity for this device is roughly between -20 and 20 °C.

If you buy a temperature measuring device, or any other type of electronic sensor for that matter, the electronics in the transmitter will be designed to compensate for the non-linearities of the sensing element. You probably won’t even know that they’re there. The manufacturer will limit the effective range of the device such that it will cut off the worst areas at the extremes. If the behavior of the sensor is not predictable and repeatable beyond certain points, those areas should be excluded.

Peter Welander, pwelander(at)cfemedia.com



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.