Machine Safety: Does a risk assessment need to be updated for a minor machine modification?

We’ve made some minor changes to several machines over the past six months but none of these modifications included the safety system. Our engineer said that there was no change in operator safety. Do we have to update the risk assessments anyway? See ANSI B11.0 – 2010 Safety of Machinery – General Requirements and Risk Assessment; OSHA recommended.

05/07/2012


J.B. Titus, CFSE"We’ve made some minor changes to several machines over the past six months but none of these modifications included the safety system. Our engineer said that there was no change in operator safety. Do we have to update the risk assessments anyway?"

   The long and short answer is – yes! This is one of the most frequently asked questions at Machine Safety seminars. Just think about the consequences for a moment. Let’s say a modification was made to the protective fencing moving a man entry gate six feet. The modification was simple enough and the existing door interlock switch continues to work just fine after being re-wired. The operator is unaffected by this change because he/she is not required to access this door. So, operator safety is unaffected as the engineer had said.

   However, if the new door location is now six feet closer to a hazard point the time distance calculations may reflect the need to raise the hazard level from Cat 3 to Cat 4. This will undoubtedly require different hazard mitigation techniques to reach the same reduced level of hazard (acceptable risk). And, how would we discover that this simple modification resulted in a serious change to overall machine safety? An updated risk assessment! This is why any modification to a machine requires that the risk assessment must be updated.

ANSI B11.0 – 2010 Safety of Machinery – General Requirements and Risk Assessment. Cover image used with permission. Courtesy: ANSI   In my opinion, referring to ANSI B11.0 – 2010 Safety of Machinery – General Requirements and Risk Assessment will answer this question in Clause 4.11 (page 27) as follows:

 4.11 Modifying and/or rebuilding a machine

   Non-standard uses or modifications of the machine, machine control system or the safeguarding can create additional hazards. A modifier and/or rebuilder of machinery shall use the risk assessment process to ensure that risks are reduced to an acceptable level. Modifiers and/or rebuilders shall, where practicable, solicit the original supplier’s recommendations regarding any proposed modification to a machine that may affect the safe operation prior to making any such changes.

   Where modifications are made to the machine/system (for example, intended use, tasks, hardware, and software), a risk assessment / risk reduction process shall be repeated for those parts of the machine/system being modified or affected.

   Within the United States I strongly recommend that manufacturers use ANSI B11.0 as one of your core industry standards for machine safety compliance. Also, it’s actually recommended by OSHA.

   Your comments or suggestion are always welcome so please let us know your thoughts. Submit your ideas, experiences, and challenges on this subject in the comments section below. Click on the following text if you don't see a comments box, then scroll down: Machine Safety: Does a risk assessment need to be updated for a minor machine modification?

Related articles:

Updating Minds About Machine Safety

Machine Guarding & The Hierarchy of Measures for Hazard Mitigation

Machine Safety – the myths of safety cultures.

   Contact: www.jbtitus.com for “Solutions for Machine Safety”.



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.