Model-based control, dead times, lag times

Distillation columns and precise composition control: Composition control is critical for economical operation of distillation columns. Model-based control techniques prevent purity problems associated with dead and lag times.


A key product variable in this depropanizer is iso-butane. Reflux flow is adjusted by a tray temperature controller to maintain iso-butane purity. Courtesy: Maverick TechnologiesFor precise composition control, on-stream process analyzers often are employed to measure composition of the critical product, such as distillation columns, among the most common unit operations for separation and purification in process industries. The purity of product streams is critical for economical operation of the column.

Modern control techniques have been developed to utilize analyzer measurements from gas chromatographs (GCs) for closed-loop, distillation column product composition control.

For example, consider the depropanizer shown in the accompanying figure. We’ll assume that the key product quality variable is the iso-butane (i-C4) content of the propane (overhead) product, which is being measured by an on-line GC. Maintaining i-C4 content just below its maximum specification limit maximizes propane recovery. The reflux flow is adjusted in cascade from a tray temperature controller, indirectly maintaining propane product composition. The operator then adjusts the tray temperature setpoint based upon feedback from the analyzer.

In practice, the tray temperature control may not work properly. The most common reason is dead and lag times between change in reflux flow and their impact on temperature. However, utilizing advanced regulatory control (ARC) techniques, such as feedforward, this cascade can work.

The next step is to implement a process identification model (PIM) and close the loop between the analyzer and tray temperature controller. Because the sample could have been injected into the analyzer up to 40 minutes prior, the PIM should be time adjusted for the tray temperature and analyzer reading. In the case of this depropanizer, a simple dead time and lag transfer function adequately delayed the temperature so that it lined up with the composition. Analysis of trend data indicated that a dead time of 34.5 minutes and lag time of 14 minutes provided a suitable match between the two variables.

We can relate the delayed tray temperature to the product composition with a simple, generally linear model:

(Temperature)delayed = K * (Composition) + Bias

Each time a new analyzer reading comes in and is validated, the controller uses the equation in two steps: It predicts the product composition based on the delayed actual temperature and then compares it with the analyzer results. Based on the error calculated from the difference of these measures, rules are used to determine a new equation bias. The equation is then inverted to calculate the new temperature controller setpoint, which is downloaded to the temperature controller. Note that control action is taken only when a new reading comes in from the GC.

This technique works well when there is an intermediate control variable, such as a tray temperature (inferential of composition), that can be correlated in time with the analyzer reading. Since feedback from the analyzer is model-based, there are no inherent shortcomings associated with the long dead time and lag, unlike conventional proportional-integral-derivative (PID) feedback control.

Jim Ford is process control consultant at Maverick Technologies.


Check out more Real World Engineering blog advice: 

No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.