Plant integration of wireless steam traps

Case study notes show how multiple vendors’ technologies enable successful wireless monitoring of steam traps.

05/22/2012


Case study notes: Last December, a team of engineers and control system specialists worked with a client to field test the installation and operation of wireless steam trap monitors in an industrial environment.

Engineers involved in the wireless sensing and monitoring project had to address two major questions:

1) Given the amount of metal and line-of-sight obstructions, would wireless work?

2) Could the wireless devices be integrated into their existing control system?

Multi-vendor integration allows remote monitoring of steam traps. Courtesy: Maverick TechnologiesWe quickly installed 30 wireless steam trap monitors on multiple floors in our steam plant. These devices are battery-operated, so no field wiring was required, and the batteries typically last three to five years. Each trap was configured to report four instrument readings: acoustic impedance, trap temperature, battery voltage, and internal board temperature. The transmitters contain software to form a self-organizing network, which allows them to work like repeaters for each other when necessary. It also allows you to add or remove transmitters as your plant’s needs change.

Three Smart Wireless Gateways from Emerson were used to communicate with the wireless transmitters. The gateways are Web-enabled, allowing connection with a laptop or other equipment via Ethernet. It is easy to communicate with the gateways and view information from each of the traps. In addition to process information, the transmitters report which other transmitters they communicate with. This allows fine-tuning of device placement to determine if signal repeaters are needed.

A ProSoft Modbus card was configured to move the instrument readings from the gateways into the plant’s existing Allen-Bradley controllers from Rockwell Automation. Thus alarms, display, and trending of the steam trap information could be added to the existing human-machine interface system.

In the five months since the system has been in service, there have been no signal-loss problems nor any failures of the wireless transmitters or gateways. This test installation has been, and continues to be, a successful demonstration of the industrial wireless technology.

- Susan Lang is project manager, Maverick Technologies. Edited by Mark T. Hoske, content manager CFE Media, Control Engineering, Plant Engineering, and Consulting-Specifying Engineer. Reach him at mhoske(at)cfemedia.com.

http://controleng.com/wireless has more industrial wireless advice.

See the "Real World Engineering Blog" at http://controleng.com/blogs



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.