16 New data acquisition devices for PCI Express and PXI Express

X Series multifunction data acquisition (DAQ) devices from National Instruments provide enhancements to analog I/O, digital I/O, onboard counters, and multidevice synchronization.

08/10/2009


At NIWeek 2009, National Instruments announced new X Series multifunction data acquisition (DAQ) devices for PCI Express and PXI Express.ncements to analog I/O, digital I/O, onboard counters and multidevice synchronization.

NI X-series DAQ devices

Simultaneous X Series devices integrate up to 16 ADCs on a single device at 2 MS/s per channel, so engineers can sample all AI channels at a high rate and with minimal phase offset.

X Series DAQ devices, which include up to 32 analog inputs (AI), four analog outputs (AO), 48 digital I/O lines and four counters, range from low-cost 250 kS/s multiplexed AI to 2 MS/s simultaneous sampling AI. Simultaneous X Series devices integrate up to 16 ADCs on a single device at 2 MS/s per channel, so engineers can sample all AI channels at a high rate and with minimal phase offset. With high sampling on all channels, simultaneous X Series devices pass large quantities of data back to the host PC, delivering a total AI throughput of up to 64 MB/s. With the added throughput of AO, digital I/O and counter operations, total throughput can surpass 100 MB/s for a single device - the practical maximum of the PCI bus. For this reason, X Series devices use the high-throughput PCI Express bus.

PCI Express offers several benefits to data acquisition applications, including dedicated bandwidth to each device of up to 250 MB/s in each direction. With this additional bandwidth, users can acquire larger quantities of analog, digital and counter data and, with the dedicated nature of the bus, engineers can easily expand their systems to include multiple data acquisition devices. The new X Series devices integrate a native PCI Express interface, which is designed to provide the full 250 MB/s of PCI Express bandwidth, as opposed to a PCI-to-PCI Express bridge interface, which limits the device bandwidth to that of the PCI bus. These devices also are optimized for low-latency I/O, which improves performance in control and single-point applications.

Advanced timing and triggering functionality on multifunction DAQ devices traditionally required onboard counters, complex code or manual signal routing to achieve specialized hardware-timed performance. New NI-STC3 technology provides X Series devices with independent timing engines for the onboard analog and digital I/O subsystems, so engineers can execute analog and digital I/O independently at different rates or together with synchronization. X Series devices include four enhanced 32-bit counters for frequency, pulse-width modulation (PWM) and encoder operations and a new 100 MHz timebase that can generate analog and digital sampling rates with five times better resolution than previous devices.

Create applications for multicore processors

By using the multithreaded NI-DAQmx driver software and NI LabVIEW graphical programming, engineers can easily create applications that execute on multicore processors for higher performance and more advanced analysis and data visualization. LabVIEW automatically generates threads for parallel sections of code that correspond to different streams of data, so engineers with little or no programming background can spend more time problem solving and less time programming the low-level implementation of their applications. They can easily synchronize two or more X Series devices with new multidevice tasks and can rapidly log the acquired data to disk by adding a single new Configure Logging function to their NI-DAQmx code. In addition, engineers can easily incorporate X Series devices into an existing data acquisition system because they use the same NI-DAQmx driver software and I/O connector as previous-generation devices.

 

- Edited by Renee Robbins, senior editor
Control Engineering News Desk

Whitepapers, Automation Resource Center from Control Engineering

 

Three National Instruments leaders offered U.S. business leaders advice about how to thrive as the country moves out of recession. The engineering-minded executives also suggested ways U.S. policymakers, economists, and financial wizards might avoid future economic disasters, in an Aug. 4 discussion.





No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Motor specification guidelines; Understanding multivariable control; Improving a safety instrumented system; 2017 Engineers' Choice Award Winners
Selecting the best controller from several viewpoints; System integrator advice for the IIoT; TSN and real-time Ethernet; Questions to ask when selecting a VFD; Action items for an aging PLC/DCS
Robot advances in connectivity, collaboration, and programming; Advanced process control; Industrial wireless developments; Multiplatform system integration
Motion control advances and solutions can help with machine control, automated control on assembly lines, integration of robotics and automation, and machine safety.
This article collection contains several articles on the Industrial Internet of Things (IIoT) and how it is transforming manufacturing.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Future of oil and gas projects; Reservoir models; The importance of SCADA to oil and gas
Big Data and bigger solutions; Tablet technologies; SCADA developments
SCADA at the junction, Managing risk through maintenance, Moving at the speed of data
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
click me