Advancing Technology: 'American Idle' - Nuclear Power

New U.S. nuclear power plants will not be operative for years, but the licensing process to allow building the first of new generation plants is nearing approval - September 2010 Control Engineering.

09/02/2010


Despite not having brought online a single new nuclear power plant in more than 30 years, the 104 nuclear generators (at 65 plant sites) currently operating in the U.S. still comprise the largest number of nuclear units in one country. Perhaps more remarkable is that refueling improvements, advances in control and safety systems, plus other technology upgrades over time, have raised the capacity factor (CF) of these plants to more than 90% on average. This is significantly higher than elsewhere or for electricity generation from other energy sources. CF is a prime parameter of power plant performance.

 
Top Countries with Nuclear Power Generators Installed and Corresponding % Electric Generation

  Country

  Number of Units

  % Electric Generation*

  U.S.

 

             104

 

                   20

 

  France

 

              58

 

                   77

 

  Japan

 

              54

 

                   26

 

  Russia

 

              32

 

                   16

 

* Other small countries with different power demands derive higher % electric generation from fewer nuclear reactors.
Source: World Nuclear Association and Control Engineering.

Cost of neglect

It borders on national oversight that not one new U.S. nuclear plant has been added in all those years. Resulting losses range widely: years of application and operating experience with new plant designs, two generations of new nuclear engineering talent, many potential high-tech jobs, and technology leadership.

Then, we have the spent-fuel storage fiasco. After 30 years of study, investigation, testing, and $10 billion spent to arrive at a solution, the Yucca Mountain, NV, nuclear waste repository site—which included digging miles of tunnels among other facility developments—has been virtually scrapped.

Spent fuel remains stored under water at individual plants, largely unchanged from the initial, temporary containment method. While this has worked on a temporary basis, nuclear waste remains an issue for the industry. Permanent solutions are within reach of engineers but require decision and empowerment.

Cautious optimism ahead

Still, positive developments are in play for the future of U.S. nuclear power. The long legal approval process to build a plant has been shortened by the Nuclear Regulatory Commission’s adoption of a combined operating license (COL)—a construction permit and operating license in one. COLs for some 17 sites are in process, but fewer plants are expected to be built due to financing difficulties and other industry uncertainties.

Leading the line for new licensing is Southern Nuclear Operating Co.’s application to build and operate two reactors near Augusta, GA, on the site of the two-unit Vogtle nuclear plant. COL approval is not expected before late 2011 or early 2012. Start of commercial operation for Units 3 and 4 is planned for 2016 and 2017, respectively, according to Southern Co.

Limited work under early site permits is ongoing at several sites. Some developers have also started long-lead-time equipment procurement, such as ordering major forgings and other engineering or limited construction activities. The reactors awaiting certification are of several so-called “advanced generation III” designs with U.S. and international origins. Overall, not more than eight new nuclear plants are expected to be online by 2020.

Another possible longer-term development is a “smaller is better” approach to nuclear plant design.

Industry experts say that only two events can stop renewal of nuclear power as part of a realistic mix of U.S. energy sources: a major accident and a terrorist attack on a plant. In the meantime, nuclear power supporters and opponents alike continue to enjoy its benefits—which amounted to 20.2% of U.S. electric power generation in 2009.

For more information, visit:

www.nrc.gov

www.southerncompany.com

www.world-nuclear.org

Frank J. Bartos, P.E., is a Control Engineering consulting editor. Reach him at braunbart@sbcglobal.net.

Also read, from Control Engineering:

Is Smaller Better for Nuclear Power Plants?



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.