Choosing RTDs and thermocouples

The two most common ways of measuring industrial temperatures are with resistance temperature detectors (RTDs) and thermocouples. But when should control engineers use a thermocouple and when should they use an RTD? The answer is usually determined by four factors: temperature, time, size, and overall accuracy requirements.


The two most common ways of measuring industrial temperatures are with resistance temperature detectors (RTDs) and thermocouples. But when should control engineers use a thermocouple and when should they use an RTD? The answer is usually determined by four factors: temperature, time, size, and overall accuracy requirements.

What are the temperature requirements? If process temperatures fall from–328 to 932 °F (–200 to 500 8C), then an industrial RTD is an option. But for extremely high temperatures, a thermocouple may be the only choice.

  • What are the time-response requirements? If the process requires a very fast response to temperature changes—fractions of a second as opposed to seconds (i.e. 2.5 to 10 sec)—then a thermocouple is the best choice. Keep in mind that time response is measured by immersing the sensor in water moving at 3 ft/sec with a 63.2% step change.

  • What are the size requirements? A standard RTD sheath is 0.125 to 0.25 in. dia., while sheath diameters for thermocouples can be less than 0.062 in.

  • What are the overall requirements for accuracy? If the process only requires a tolerance of 2 °C or greater, then a thermocouple is appropriate. If the process needs less than 2 °C tolerance, then an RTD is the only choice. Keep in mind, unlike RTDs that can maintain stability for many years, thermocouples can drift within the first few hours of use.

Although not a technical point, price may be another consideration. An average thermocouple costs approximately $35, while an average RTD costs $55. Cost of extension wire must also be considered. Thermocouples require the same type of extension wire material as the thermocouple, which can cost up to $1 per ft. Standard nickel-plated, teflon-coated RTD wire averages pennies per ft.

RTD basics

Once parameters are defined, the type of RTD or thermocouple is chosen. RTDs provide a resistance vs. temperature output and are passive devices, needing no more than 1.0 mA to run. The most common RTD is a 100 ohm, platinum sensor, with an alpha coefficient of 0.00385 ohms/ohm/C. It can be ordered as DIN A or DIN B which specifies the initial accuracy at 0 °C (ice point) and the interchangeability over the operating range. IEC 751 states that DIN A is 0.15 °C

RTDs can also be constructed from nickel, copper, or nickel/iron. Each metal has a different alpha coefficient and operating range. An RTDs alpha coefficient must be matched to its instrumentation or an error of several degrees can occur.

About thermocouples

Thermocouples can be made with any combination of two dissimilar materials. ISA recognizes twelve thermocouples. Eight of the 12 have letter designations including Type J, Type K, Type T and Type E.

The most common determining factor for chosing thermocouple type is the temperature range of its intended application. Type J is suitable for a temperature range of 32 to 1,400 °F (0 to 759.99 °C). Type K is appropriate for a temperature range of 32 to 2,300 °F (0 to 1,259.99 °C). Type T handles a temperature range of–300 to 700 °F (–184.44 to 371 °C). Type E fits a temperature range of 32 to 1,600 °F (0 to 871.11 °C).

Standard limits of error and special limits of error must also be considered. These values relate to the purity of the wire used to manufacture the thermocouple. For very little additional cost, thermocouple specifiers can often improve accuracies greatly (100% or greater).

Specifying the correct thermocouple or RTD for an unconventional application may be a difficult task. Many manufacturers of RTDs and thermocouples offer applications engineering support to help customers select the right combination of temperature measurement equipment.

Author Information

Jim Sulciner is the national sales manager for Burns Engineering (Minnetonka, Minn.), a RTD manufacturer. Comments? E-mail

Quick selection guidelines


Offer stable output within broad temperature ranges;

Can be recalibrated for verifiable accuracy;

Are stable over the long term;

Follow a more linear curve than thermocouples;

Have high sensitivity; and

Provide accurate reading over narrow temperature spans.


Operate at temperatures over1,200°F (648.88°C);

Perform in extremely rugged applications;

Offer very fast response to temperature changes;

Are small in physical size; and

May have a lower initial cost in some applications.

No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Controller programming; Safety networks; Enclosure design; Power quality; Safety integrity levels; Increasing process efficiency
Additive manufacturing benefits; HMI and sensor tips; System integrator advice; Innovations from the industry
Robotic safety, collaboration, standards; DCS migration tips; IT/OT convergence; 2017 Control Engineering Salary and Career Survey
Featured articles highlight technologies that enable the Industrial Internet of Things, IIoT-related products and strategies to get data more easily to the user.
This article collection contains several articles on how automation and controls are helping human-machine interface (HMI) hardware and software advance.
This digital report will explore several aspects of how IIoT will transform manufacturing in the coming years.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Mobility as the means to offshore innovation; Preventing another Deepwater Horizon; ROVs as subsea robots; SCADA and the radio spectrum
Future of oil and gas projects; Reservoir models; The importance of SCADA to oil and gas
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me