Compressed air: Find the leaks, lower the pressure, and measure the results

12/28/2012


No savings will be realized until the volume of air required to support leaks is reduced and a measureable reduction in compressor supply power achieved.

The leak-hunting activity is usually allocated to a member of the maintenance staff. This task is usually treated as an event driven by a corporate energy leader as part of a cost reduction goal. Even though an ultrasonic leak detector is reasonably easy to use, there is still a learning curve that can only be traversed through experience. Consequently, the time allotted to locating leaks by a technician using the tool for the first time or annually delivers marginal results.

Without a target or measureable goal, any number of identified leaks can be considered sufficient. The most significant issue associated with achieving savings can be attributed to core competency and responsibility. Maintenance teams are responsible for production equipment and subsystems required to support operations.

Because production and process goals are defined, measured, and monitored, delivering operation goals is the priority and repairing identified leaks falls to the bottom of the priority list. Without a measurable validation process, the majority of identified leaks typically remain unrepaired.

As a global organization, Ingersoll Rand has developed standard work process and tools to support a formal leak assessment program. When executing our leak assessments, it is common to find a significant volume of leaks that internal resources never identified, in addition to other leaks with old tags still in place.

In addition to identifying leaks, it is important to quantify and prioritize all leaks based on volume. A prioritized list of leaks can be used to develop leak repair objectives. A “better practice” will include a third-party validation process to measure targeted leaks and confirm they are repaired. 

Lower the pressure

The second most frequently addressed “good practice” is lowering compressed air system pressure. For positive displacement compressors, like rotary screw and reciprocating compressors, reducing pressure at the discharge of the compressor will reduce the input power. It is important to note that the actual reduction in compressor power can vary depending on design and current operating pressure.



ROBERTO , TX, Brazil, 01/11/13 04:55 PM:

A no load test , made in a holiday gives you also a good measure of your invisible losses
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.