IP-all-the-way is the way to go

To take full advantage of building management systems, we need Internet protocol all the way down to the simplest devices.

07/23/2013


Varun Nagaraj is senior vice president and general manager, Internet of Things, at Echelon Corp. He has more than 20 years of high-tech product planning and strategy experience. He holds a BSEE from IIT Bombay, a master’s in computer engineering from NortLately at industry events, or talking with customers, beneath the curiosity about the Internet of Things (IoT), I hear some resistance. In particular, there’s a brewing debate about how far Internet protocol (IP) should go in buildings’ networks. 

Today, IP can be found in gateways or supervisory controllers within a building network. But to realize IP’s simpler, lower-cost management benefits, we need IP-all-the-way to the fieldbus controllers and to the smallest, lowest-powered devices, including sensors and actuators.

I can hear the objections. IP is expensive, so how can we afford to IP-enable below the gateway/supervisory controller level? Aren’t IP networks complex to set up, erasing the ease-of-management argument? What about security? Doesn’t IP’s increased attack surface practically invite hackers to mess with your network? And why add another protocol to the legacy ones already in place and working just fine? 

These are understandable concerns, but I stand by my advocacy of IP-all-the-way—specifically, IPv6 (the IP version required to grant enough addresses for the billions of devices out there) all the way to the fieldbus and device input/output (I/O) level. Let me explain why.

It’s true that currently available silicon makes IP-enabling, low-cost devices cost-prohibitive. But next-generation system-on-chip (SOC) technology will provide the makers of controllers, sensors, actuators, and similar devices with everything they need to IP-enable small, low-power, low-cost devices. I’m not talking about vanilla IP technology. These new IP chips will include a secure IP stack, a range of connectivity options (wired and wireless), enough processing capability with low power consumption to run sufficient application code, and software services. 

Important to this scenario is the concept of communities of devices: a distinct segment within the broader IoT in which devices work cooperatively with each other to achieve a larger goal, such as the comfort of an entire building. A community of devices can be IP-enabled, but it doesn’t necessarily mandate Internet connectivity. It operates primarily as an autonomous and resilient peer-to-peer network. In fact, today’s building network is an example of a community of devices that includes sensors, actuators, and various controllers working harmoniously to optimize comfort, safety, and energy efficiency. 

Another objection to an all-IP building network is the upfront planning complexity. Yes, compared to a fieldbus based on twisted pair wiring or compared to simple digital or analog I/O, it’s more complicated to address a particular device with IP. On the other hand, a bit of early complexity is well worth the long-term gains in flexibility. An all-IP network is the simplest, fastest, and most cost-effective way to adapt and change over time. 

Then there’s the issue of security. Many building networks have grown accustomed to security through obscurity, depending on the chaotic mixture of simple wires and cables to thwart potential hackers. In this environment, the very cohesiveness of IP is viewed as a security threat. 

If we believe the Internet works—and clearly, it does—then we also must believe that methods exist to secure IP networks. The key is embedding security directly into IP chips, where Internet-proven security mechanisms are transparent to device developers as well as building network owners. We don’t have to resort to stone-age technologies to implement secure networks in modern all-IP buildings. 

As for integrating IP with legacy protocols, today’s accepted approach for interconnecting networks is through gateways that map functionality between different protocols. But what if we implement gateway functionality in the device itself, through the IP chip? A single device could present itself as an IP device, or a BACnet-over-IP device, or a LonWorks-over-IP device, at the push of a button. And it could integrate multiple media types as easily as multiple protocol types. 

IP-all-the-way in building networks remains an aspiration, I admit. IP-enabling the very lowest-cost devices might never make economic sense. But even aspirationally, IP-all-the-way is an important commitment. The benefits of IP in building networks are clear, but we won’t realize the full potential unless we go all-in. 

Talk to your clients about IP, and start pushing IP as far down into the network as you can. Your clients will thank you.


Varun Nagaraj is senior vice president and general manager, Internet of Things, at Echelon Corp. He has more than 20 years of high-tech product planning and strategy experience. He holds a BSEE from IIT Bombay, a master’s in computer engineering from North Carolina State University, and an MBA from Boston University



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Big plans for small nuclear reactors: Simpler, safer control designs; Smarter manufacturing; Industrial cloud; Mobile HMI; Controls convergence
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.