Looking at electric drive efficiency

variable-frequency drives (VFDs) provide dramatic energy savings in myriad applications with varying loads and speeds. While power and energy savings are key benefits, VFD efficiency is also of interest because drives can experience significant efficiency losses at partial load operation-much like electric motors.

07/01/2009


Five makes of VFDs tested had efficiency variations (bands) as shown for 50 hp (37 kW) units running at different speeds - along with larger characteristic efficiency drop-off at reduced torque and speed.

Few will dispute that variable-frequency drives (VFDs) provide dramatic energy savings in myriad applications with varying loads and speeds. While power and energy savings are key benefits, VFD efficiency is also of interest because drives can experience significant efficiency losses at partial load operation—much like electric motors. Yet motors have received predominant attention for energy efficiency, including development of recognized test procedures and standards. A broader look at “motor system” efficiency must recognize the effect of VFDs.

Recent progress in this area includes work done at the energy technology labs of Hydro-Quebec's (Canada) Research Institute. Findings of the underlying study, “Variable Frequency Drive Testing,” have been presented at Motor Summit 2008 (Zurich, Switzerland), MEPSA 2009 (Sydney, Australia), and 2009 Motor, Drive & Automation Systems Conference (Orlando, FL) by Pierre Angers, an engineer at Hydro-Quebec.

“Published VFD efficiencies at other than full rated power are scarce,” says Angers. “There is no recognized VFD efficiency standard for comparing different makes of drives.” Efficiency is the highest around 100% speed, which is just where you don't want to use variable-speed drives, hence most available efficiency values are virtually “useless,” Angers explains.

Goals of the project were to establish an efficiency testing procedure for VFDs, motors, and VFD-motor combinations—as well as to enable efficiency comparison between various VFD systems. Angers has tested five major makes of VFDs, which powered three sizes of induction motors (10, 50, and 100 hp/7.5, 37, 75 kW) at various loads and speeds. For each test run a series of 20 test points ranged widely over “% speed” and “% nominal torque” values (25-100% speed and 10-100% torque). Drive manufacturers' names remain proprietary. Test setup measured efficiency as a ratio of output to input power.

Preliminary results show 2-8% variation in VFD system efficiency, especially at low loads and speeds. Efficiency variation between different brands of VFDs was substantially less (see diagram). However, variability of VFD efficiency is further impacted by factors such as drive temperature, supply voltage (and voltage unbalance), switching frequency, and drive options like active front-end, reactors, or output filters.

One novel aspect of Angers' research is presentation of motor system efficiency results as a contour map, with percent nominal speed and percent torque serving as other variables. A typical conveyor application plots as a horizontal line (constant torque) across the efficiency contours, while a pump/fan application plots as a cubic system curve.

The work described here is the basis of a protocol for testing VFD efficiency. Two proposed standards are in draft status: Canadian standard (CSA C838) Variable Frequency Drives and International Electrotechnical Commission standard IEC 60034-2-3.

Users of VFDs obtain energy savings from matching motor speed to load requirements; in addition, they need to be able to compare efficiency of different electric drive brands for their applications.


Author Information

Frank J. Bartos, P.E., is a Control Engineering consulting editor. Reach him at braunbart@sbcglobal.net .




No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.