Machine Safety: OSHA’s top 10 cited violations for 2013

Are you very aware of OSHA’s top 10 citations for 2013? Is this because of your excellent safety culture and organizational diligence? Or, is it because you’ve been cited by OSHA?

12/30/2013


OSHA top 10 violations for 2013Are you very aware of OSHA’s top 10 citations for 2013? Is this because of your excellent safety culture and organizational diligence? Or, is it because you’ve been cited by OSHA? It seems to me, "Here we go again!"

Does OSHA’s top ten list ever mix it up much at all? I’ve been watching this list fairly close for the past few years, and I can’t overtly state any significant changes. I think these standards move around a little but don’t they all pretty much fall into the top ten year after year?

The preliminary figures for the OSHA FY 2013 Top 10 are:

Standard Total Violations

1. 1926.501 – Fall Protection 8,241

2. 1910.1200 – Hazard Communication 6,156

3. 1926.451 – Scaffolding 5,423

4. 1910.134 – Respiratory Protection 3,879

5. 1910.305 – Electrical, Wiring Methods 3,452

6. 1910.178 – Powered Industrial Trucks 3,340

7. 1926.1053 – Ladders 3,311

8. 1910.147 – Lockout/Tagout 3,254

9. 1910.303 – Electrical, General Requirements 2,745

10. 1910.212 – Machine Guarding 2,701

Courtesy of OSHA: www.osha.gov/Top_Ten_Standards.html 

In my last few blogs on this subject I’ve indicated that several of these standards relate directly to machine safety, not only item #10 Machine Guarding. In November’s Control Engineering magazine on page 26, a short news article asks: “Were you on the OSHA top 10 list of violations?” The news story goes on to say: “OSHA violations related to machine safety include electrical and wiring methods (5), Lockout/tagout (8), electrical (9), and machine guarding (10)." This mixes the order up a bit, but I recall these same four violations reported in previous years. There were 27,186 total violations in 2012, and 42,502 violations in 2013. So, doubling the number of OSHA reported violations has little direct impact in the types of violations.

My take away is as follows: we’ve still got a lot of work to do if we truly want Machine Safety to not be reported in OSHA’s top 10 list of violations. What is your take away?

Please use these blog posts for advance your machine safety efforts. Do you have some specific topic or interest that we could cover in future blog posts? Add your comments or thoughts to the discussion by submitting your ideas, experiences, and challenges in the comments section below.

Related articles:

Machine Safety: OSHA Top 10 Violations for 2012

 

Machine safety pays off – by JB Titus

 

Machine Safety – does OSHA reference consensus standards for compliance?

 

Machine Safety: Is OSHA okay with my 'acceptable' risk mitigation?

 

Integrated Safety Systems: Ensuring Safety and Operational Productivity - by the Aberdeen Group

 

OSHA – search for near miss

 

 

Contact: www.jbtitus.com for “Solutions for Machine Safety.”



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.