Machine Safety: Verification is not validation

Know the 5 steps of the functional safety lifecycle. To perform functional safety and comply with safety standards like ISO 13849-1 and ISO 13849-2, design engineers need to know how to perform verification and validation measures; they are not the same step.

05/20/2014


To perform functional safety and comply with safety standards like ISO 13849-1 and 2, design engineers need to know how to perform verification and validation measures. But aren’t they the same step?

In the functional safety lifecycle, 1) Perform risk assessment, 2) Examine functional requirements, 3) Design and verify mitigation, 4) Install and validate, and 5) Manage, change, and improve. Courtesy: Control Engineering Machine Safety Blog, JB Titus & Associates

The most immediate answer is NO!

Best-in-class companies are generally adopting the “lifecycle” design model when approaching functional safety design requirements. An example is shown in this graphic of the functional safety lifecycle:

1) Perform risk assessment

2) Examine functional requirements

3) Design and verify mitigation

4) Install and validate

5) Manage, change, and improve.

ISO 13849-1 requires that during the design stage a verification step is performed (lifecycle step #3). For example, see clause 4.7 on page 26 of the standard [talking about Safety Related Parts of The Control System (SRP/CS)]:

4.7 Verification that achieved PL meets PLr

“For each individual safety function the PL of the related SRP/CS shall match the required performance level (PLr).... The PL of the different SRP/CS which are part of a safety function shall be greater than or equal to the required performance level (PLr) of this safety function.”

Validation is a different step. While verification is often performed by someone other than the original designer during the design phase, validation is performed during the build and/or installation stage (lifecycle step #4). The goal of validation is to acknowledge that the required safety function is actually achieved for any one hazard in all modes of operation. For example, see clause 8 on page 41 of the standard:

8 Validation

“The design of the SRP/CS shall be validated (see Figure 3). The validation shall demonstrate that the combination of SRP/CS providing each safety function meets all relevant requirements of this part of ISO 13849. For details of validation, see ISO 13849-2.”

The above requirements are for the safety related parts of the control system (SRP/CS) for a machine’s overall control system. Additionally, ISO 13849-1 and 2 also cover the software of a control system, which also includes requirements for verification and validation of application software for all safety functions.

It is my opinion that this information could help clear up possible confusion over the terms "verification" versus "validation" for functional safety applications. If you have additional understandings or clarifications please submit your ideas, experiences, and challenges in the comments section below.

Related articles linked in the text and the bottom of this post, follow:

The Safety Standards Maze, 3 Comments: More Standards, Validation

Machine Safety: safety system validation and daisy divination

Verification and validation by Lenze 

Contact: www.jbtitus.com for “Solutions for Machine Safety”.



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Learn how to create value with re-use; gain productivity with lean automation and connectivity, and optimize panel design and construction.
Go deep: Automation tackles offshore oil challenges; Ethernet advice; Wireless robotics; Product exclusives; Digital edition exclusives
Lost in the gray scale? How to get effective HMIs; Best practices: Integrate old and new wireless systems; Smart software, networks; Service provider certifications
Fixing PID: Part 2: Tweaking controller strategy; Machine safety networks; Salary survey and career advice; Smart I/O architecture; Product exclusives
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Look at the basics of industrial wireless technologies, wireless concepts, wireless standards, and wireless best practices with Daniel E. Capano of Diversified Technical Services Inc.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.