Manufacturer focus: Designing labs, research buildings

Labs and research facilities house sensitive equipment and must maintain very rigid standards. Two manufacturers provide insights.

05/28/2013


Rick Hermans, Applications Director, Daikin McQuay. Courtesy: Dalkin McQuayVictor Neuman, Health Care/Lab Engineer, Schneider Electric. Courtesy: Schneider Electric

Participants

Rick Hermans, Applications Director, Daikin McQuay

Victor Neuman, Health Care/Lab Engineer, Schneider Electric

http://www.schneider-electric.com

 


CSE: What tools or knowledge do engineering schools need to provide young engineers in order to successfully specify or design systems for labs? 

Daikin McQuay: Engineering schools must provide students with the fundamental physics, psychrometrics, thermodynamics, and heat transfer knowledge as it applies to HVAC in general. Architectural engineering schools provide more practical skills in how to put HVAC systems together in concept for laboratory applications, specifically with respect to ventilation and the relationship between hood exhaust, make-up air, and static pressure control.

Schneider Electric: I started in lab design in 1983 when I was hired by the visionary lab planner Earl Walls, who passed away in the last year. He was a proponent of lab "modularity." The only constant of scientific research is change. Teaching modularity in design allows laboratory building to adapt to changes in the building which are needed to account for advances in scientific methods.

CSE: What are some common missteps that engineers might make on a laboratory project? Any tips you can provide? 

Schneider Electric: In lab pressurization control, there is a common misstep of locating the variable air volume (VAV) duct with its pitot flow sensors too close to the takeoff from or to the supply duct or exhaust duct. Flow accuracy of this pitot sensor is not crucial in office buildings but it is vitally important to laboratory pressurization controls. While more accurate sensors are recommended, if you are using pitot flow sensors in your lab, it is imperative that there be at least three duct diameters of straight duct at the inlet of the pitot and one duct diameter of straight duct at the exit of the pitot flow sensor. Many engineers feel that straight duct is not necessary when using venturi valves. However, our work with commissioning agents have made us very aware that even with venturi valves it may be required to have a length of straight duct for the commissioner to insert a removable pitot tube in order to certify the venturi valve's performance.

Daikin McQuay: Too many designs are overly complicated. They use exotic equipment and controls when more simple designs will suffice. Labs are special, to be sure, but they can be solved with simple designs that are understandable, effective, and efficient. One tip would be to pay attention to the building envelope, especially the interior walls which are critical elements in maintaining static pressure control between spaces.

CSE: Please describe a recent lab project you’ve worked on—share problems you’ve encountered, how you’ve solved them, and aspects of the project you’re especially proud of. 

Daikin McQuay: One past project was interesting and instructional from an academic perspective. The lab spaces were laid out in 10-ft modules with moveable partitions. The ventilation had to be flexible to accommodate various future revisions of lab space along these modules. The solution was a common vertical plenum space which served both as an air recirculation corridor and a utility corridor with connections of utilities in the same 10-ft intervals. 

Schneider Electric: Schneider Electric recently completed a major animal breeding facility in Asia that was particularly complex. The engineer had specified that the entrance airlocks to each major animal holding room were to have five cascading pressure levels. This was accomplished to everyone's satisfaction with a cooperative effort of the consulting engineer, owner, commissioning agent, and Schneider Electric as the building automation provider. In addition, the system was required to monitor and log pressure readings at each point every second.

CSE: When designing a lab that is part of a multi-use building (such as in a hospital or university building), what unique challenges do you have?

Schneider Electric: The challenge in a university lab is balancing the open environment of a university with the security needed for scientific research. Scientists appreciate large open plan labs, but this is a challenge when planning the airflow containment and pressurization control.

Daikin McQuay: If a lab is not a single, purpose-built structure, you are constrained by the architecture of the other functions in the building. Since labs have unique ventilation requirements, you spend a lot of time trying to accomplish those ventilation designs in an architecture not meant for them. The most obvious of these is the fume hood exhaust system.

CSE: Describe your involvement in a recent integrated project delivery (IPD) lab project or research facility. 

Daikin McQuay: The role was as owner’s representative. The duties were to write requests for proposal and to assist in the selection of the IPD team members, negotiating the common contract, and providing owners input on the design development. Since the lab was so unique that neither the owner nor the design team had ever done one before, the design process was a journey of discovery that couldn’t have been accomplished with any other project delivery process.


<< First < Previous 1 2 3 Next > Last >>

No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Big plans for small nuclear reactors: Simpler, safer control designs; Smarter manufacturing; Industrial cloud; Mobile HMI; Controls convergence
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.