Motion control: To network or not to network?

12/02/2013


Machine controller cards

Figure 5: Machine controller cards combine a general purpose microprocessor with a dedicated motion controller. Increasingly, the motion amplifiers are located right on the card. Courtesy: Performance Motion DevicesThe major alternative to distributed drives is a machine controller card, also called a motion control card. The distinction is that a motion control card connects via a backplane bus to a separate motherboard or processer card, but here we will refer to stand-alone single-card controllers and backplane motion cards as machine controller cards.

In the machine controller approach a microprocessor holds the machine's application code, and a motion controller IC, also called a motion processor, generates profiles, does servo loop closure, and manages the time-critical elements of axis control. Note that it is possible, particularly for simple control applications, for the machine application microprocessor and the motion processor to be one and the same.

The advantages of the machine controller card approach are many-fold including easier serviceability since repair of the entire controller card is a simple swap-out. Another advantage is reduced wiring since the amplifiers are located on the card. Finally, the physical form factor of the card along with the connector interfaces can be tailored to suit the application.

There are two major variations of machine controller cards: off-the-shelf and custom built. Off-the-shelf cards, particularly bus-connected motion cards, have been around for a long time and are available from several different vendors.

Custom built cards, while more work on the design side, are also a strong choice. The most important trend here is integration of the amplifier, either IC or module-based, directly onto the card.

Another trend is use of off-the-shelf IC-based motion controllers. These units provide profile generation, servo loop closure, commutation, and a myriad of time-critical functions such as automatic safety responses, programmable breakpoints, and other types of automatic motion axis management.

How to choose a network

Figure 6: Today's solderable amplifier modules can provide output of a kilowatt or more to drive dc brush, brushless dc, and step motors. Courtesy: Performance Motion DevicesHere’s how to select a motion control network. Certain factors may make one architectural approach more suited than another.

When considering a distributed motion network, try to anticipate the kinds of signaling that will be required in your application. Does the behavior of the motion depend on the status of signals located on another part of the machine? Will you place sensors, and other non-motion controlled actuators, such as relays, on the network bus? How quickly does the motion have to shut down if an error occurs?

Another important consideration regarding how, and how much, you can use a network-based approach is the mechanical organization of the connected machine. This issue addresses questions such as, “How will the machine be serviced if electronics are physically distributed throughout the machine?” Although the traditional card rack that the technician services may be a mess of wires, there is something to be said for keeping everything under one roof. Serviceability and lifetime ownership cost strongly affect control system design choices.

Remember also that distributing the control by placing amplifiers near the motors may not always be feasible for weight, heat, or other environmental reasons. The traditional control rack cabinet can be air conditioned and insulated from the machine operating environment. This is often not possible if the controls are distributed.

When is one control approach used over another? There is no easy or simple answer, and sometimes two architectures can be used equally well for a given application.

In broad terms, the more cost sensitive the application, the more likely it is that the person designing the motion application will design a card and, depending on power level, integrate on-board amplifiers. When designing a card, it is possible to choose exactly the connectors needed and set the form factor of the card for that particular motion application.

Figure 7: Off-the-shelf motion control integrated circuits (ICs), also called motion processors, provide profile generation, servo loop closure, and various other dedicated motion functions. Courtesy: Performance Motion DevicesHighly synchronized applications such as machine tools will gravitate toward multi-axis motion cards or a tightly coupled distributed drive approach. These drives allow a lot of flexibility in motor type and power range. Don't forget that a motion control card will be needed for overall path generation, or you will use a PC running dedicated G-code software.

A large middle ground of applications, such as medical automation, semiconductor automation, scientific instrumentation, and low-power general automation, can be served by several approaches including off-the-shelf machine controller cards, custom-built machine controller cards, or loosely coupled distributed drives.

- Chuck Lewin is founder and vice president of engineering, Performance Motion Devices. Edited by Mark T. Hoske, content manager, CFE Media, Control Engineering, mhoske(at)cfemedia.com.

ONLINE

At bottom of this article, look for related articles on motion control.

Key concepts

  • Understanding motion architectures can help with machine design and network selection and design.
  • Two motion control devices include distributed drives and machine controller cards.

<< First < Previous 1 2 Next > Last >>

No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.