Not Again – E-Stops Do Not Equal Machine Safety

How many times does this issue come up? An e-stop device is not a safety device! Therefore, it’s not a part of the safety related parts of a control system (SRP/CS). Then, why is an e-stop device so often confused as being part of the safety design for a machine?

07/19/2011


Jokab Safety giant E-Stop at Pack Expo 2010How many times does this issue come up? An e-stop device is not a safety device! Therefore, it’s not a part of the safety related parts of a control system (SRP/CS). Then, why is an e-stop device so often confused as being part of the safety design for a machine?

JB Titus, CFSE     In my opinion, we should first look at the term, Functional Safety. “Functional Safety” was introduced to industry by IEC 61508: 1998. IEC 61508, Functional Safety of Electrical/Electronic/Programmable Electronic Safety-related Systems, defines it as the following. IEC 61508 Definition:

  • Safety is the freedom from unacceptable risk of physical injury or of damage to the health of people, either directly, or indirectly as a result of damage to property or the

environment.

  • Functional Safety is part of the overall safety that depends on a system or equipment operating correctly in response to its inputs.

Elobau E-stop switches     In a functional safety system there are electrical and electronic components like; safety relays, interlock switches, safety contactors, safety PLC’s and drives, safety motion scanners and light curtains, and safety net works. All of these technologies are then designed to form a safety system and are dedicated to perform specific safety functions. These safety functions are usually determined as required to mitigate certain hazards identified by the risk assessment process.

Carlo Gavazzi e-stops     Not mentioned above is the e-stop device. I believe that’s because e-stops have a broader range of application, must be manually activated, and are not dedicated to perform a safety function. The colors, red push buttons with a yellow background, may be confusing. But, they are not required and applied to always perform safety-related functions. According to NFPA 79; 2007, Electrical Standard for Industrial Machinery, e-stops are required for “final removal of power to the machine actuators” to achieve either a Category 0 or Category 1 stop (Clause 9.2.2 Stop Functions and Clause 9.2.5.4.1 Emergency Stop). Many times the e-stop may be activated due to non safety-related functions, such as; material feed issues, impending machine jams, maintenance issues, or machine set-up requirements.

     Does this help clarify the often misunderstood e-stop versus safety device issue?

     Your comments or suggestion are always welcome so please let us know your thoughts. Submit your ideas, experiences, and challenges on this subject in the comments section below. Click on the following text if you don't see a comments box, then scroll down: Not Again – E-Stops  Machine Safety.

     Did you see the Safety Integration Webcast?

     Related articles:

E-Stops and Your Compliance

E-Stops Aren’t Safety Devices

How to Integrate Safety

     Contact: www.jbtitus.com for “Solutions for Machine Safety”.



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Learn how to create value with re-use; gain productivity with lean automation and connectivity, and optimize panel design and construction.
Go deep: Automation tackles offshore oil challenges; Ethernet advice; Wireless robotics; Product exclusives; Digital edition exclusives
Lost in the gray scale? How to get effective HMIs; Best practices: Integrate old and new wireless systems; Smart software, networks; Service provider certifications
Fixing PID: Part 2: Tweaking controller strategy; Machine safety networks; Salary survey and career advice; Smart I/O architecture; Product exclusives
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Look at the basics of industrial wireless technologies, wireless concepts, wireless standards, and wireless best practices with Daniel E. Capano of Diversified Technical Services Inc.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.