PID math demystified, part 4

You’ve see the equations, but have you thought about how those elements work together? Part 4: Feed forward

06/10/2014


In the first three blog posts (see Part 1, Part 2, and Part 3) we covered the basics of PID math. We started with the basic proportional-only controller and worked in the integral and derivative components. Well before get too far, let’s review the proportional-only controller:

u(t) = Kpe(t)

u(t)
is the output of the controller at the end of the scan. If the output of the controller is a valve, then the output is the valve position that the controller is requesting after it has seen the inputs.

Kpe(t) is the proportional component, the P in PID. e(t), usually called “error,” is simply the difference between the setpoint and the process variable. Kp gain is a factor that is multiplied by the error to give you the new output—the new valve position. It’s that simple. The error at that instant of the scan is calculated and the new output is calculated.

The pseudo code that we discussed was:

Error = Setpoint – ProcessValue
Output = K * Error

With this code the output changes immediately after the error changes. I like to use a cruise control on a car as an example. As soon as the car starts to slow down as it starts to climb a hill, the change in error (speed) immediately causes the output to change.

But what if you know that the speed is about to slow down? What if you can see the hill coming? That’s where feed forward comes in. The first step is detecting a condition that will affect the process value. This can be an upstream flow rate that affects a level controller, a pressure change that affects a flow controller or any number of variables. The important thing is that the feed forward signal has to have a predictable affect on the controlled variable.

The math behind it is conceptually pretty simple. The feed forward signal is multiplied by a gain and then added directly to the output:

Error = Setpoint – ProcessValue
Output = K * Error + FeedForward * Kf

That way as long as the feed forward signal doesn’t change, the controller is not affected. But, a change in the feed forward signal immediately makes a proportional type shift in the output.

The math does get more complicated when the time that it takes for the signal to affect the process value has to be considered. In that case a lead or lag calculation must be done to slow down or speed up the feed forward signal. But that’s a topic for the next post.

This post was written by Scott Hayes. Scott is a senior engineer at MAVERICK Technologies, a leading automation solutions provider offering industrial automation, strategic manufacturing, and enterprise integration services for the process industries. MAVERICK delivers expertise and consulting in a wide variety of areas including industrial automation controls, distributed control systems, manufacturing execution systems, operational strategy, business process optimization and more. 



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Learn how to create value with re-use; gain productivity with lean automation and connectivity, and optimize panel design and construction.
Go deep: Automation tackles offshore oil challenges; Ethernet advice; Wireless robotics; Product exclusives; Digital edition exclusives
Lost in the gray scale? How to get effective HMIs; Best practices: Integrate old and new wireless systems; Smart software, networks; Service provider certifications
Fixing PID: Part 2: Tweaking controller strategy; Machine safety networks; Salary survey and career advice; Smart I/O architecture; Product exclusives
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Look at the basics of industrial wireless technologies, wireless concepts, wireless standards, and wireless best practices with Daniel E. Capano of Diversified Technical Services Inc.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.