Plant Engineering Magazine's Exclusive Guide To Synthetic Lubricants

Key concepts These lubricants reduce wear and provide long life. Synthetics can be formulated with a combination of features to satisfy specific application requirements.



These lubricants reduce wear and provide long life.

Synthetics can be formulated with a combination of features to satisfy specific application requirements.

The chart lists the product offerings from 73 companies.

Synthetics are the logical lubricant choice in a number of applications, including:

  • Equipment failure or excessive downtime is attributed to ineffective lubrication products or practices

      • Performance demands are beyond the capabilities of mineral-based petroleum products

          • High or low temperatures (-75-500 F) are encountered.

            • Manmade synthetics reduce wear by providing a better lubricant film in the load zone or nonconforming surface of bearings, gearboxes, compressors, rotary shaft seals, vacuum and diaphragm pumps, valves, and hydraulic systems. Reduced maintenance, parts replacement, and energy costs often result. Synthetic lubricants also provide long life because of their enhanced thermal and oxidative stability, which reduce the formation of sludge, corrosion, and deposits.

              The major drawback to synthetic lubricants is initial cost, which is typically about three times higher than mineral-based products. However, the initial price premium is usually recovered over the life of the product, which is about three times longer than conventional lubricants. Because of the initial expense, using synthetics in systems experiencing leakage or contamination is not a practical choice.

              The chart presented on the following pages serves as a guide to selecting and applying synthetic gear, bearing, hydraulic, and compressor oils; and three high/ extreme pressure greases. The chart, which is updated every 3 yr, is based on information supplied by the 73 companies who responded to a written request from Plant Engineering magazine.

              Products presented in the listings are categorized by viscosity. However, there are several other important variables that should be considered when selecting and applying synthetic lubricants. These factors include pour and flash points, demulsibility, lubricity, rust and corrosion protection, thermal and oxidation stability, antiwear properties, compatibility with seals and paints, and compliance with testing and standard requirements.

              Products presented in each category are not necessarily interchangeable or compatible. These two features depend on a variety of interrelated factors, and each application requires an individual analysis.


              A properly selected synthetic product provides the same basic lubrication functions as mineral oils. However, synthetic lubricants can be formulated with a combination of features to satisfy specific application requirements that petroleum products cannot usually match.

              Performance characteristics of synthetic lubricants derive from the physical and chemical properties of the base fluid and effects of additives introduced into the final product. Physical and chemical qualities include viscosity-temperature behavior, low-temperature fluidity, volatility, compatibility with paints and elastomers, ability to dissolve chemical additives, compatibility with petroleum, and hydrolytic stability. Additives are introduced to influence, to a greater or lesser degree, oxidation stability, load-bearing ability, and corrosion protection.

              The table below shows the relative performance characteristics of seven types of synthetic lubricants and a paraffinic mineral oil.


              There are several major classes of synthetic lubricants.

              • Synthesized hydrocarbons, such as polyalphaolefins and dialkylated benzenes, are the most common type. These products provide performance characteristics closest to mineral oils, and are compatible with them. They serve as engine and turbine oils, hydraulic fluids, gear and bearing circulating oils, and compressor lubricants.

                  • Organic esters, such as dibasic acid and polyol esters, easily accept additives, which enhance their applicability for finished product formulations, such as crankcase oils and compressor lubricants.

                      • Phosphate esters are well suited for fire resistance applications.

                          • Polyglycols are applied for lubricating gears and bearings, and compressors handling hydrocarbon gases.

                              • Silicones are chemically inert, nontoxic, fire resistant, and water repellent. They have low pour points and volatility, good low-temperature fluidity, and good oxidation and thermal stability at very high temperatures.

                                • It is important to remember that synthetics are as different from each other, as they are from petroleum lubricants. Their performance and applicability to any individual situation depend on the quality of the synthetic base stock and additive package.

                                  Consulting the manufacturer early in the initial selection process is the best approach to ensuring the right product is selected for the application.

                                  -Ron Holzhauer, Managing Editor, 630-320-7139,;

                                  Cheryl Firestone, Senior Editor, 630-320-7136,

                                  Performance characteristics of several lubricants

                                  <table ID = 'id2736707-65-table' CELLSPACING = '0' CELLPADDING = '3' BORDER = '1' STYLE = 'background-color: #FFFFFF'><tbody ID = 'id2736717-65-tbody'><tr ID = 'id2736720-65-tr'><td ID = 'id2736722-65-td' VALIGN = 'top' STYLE = 'background-color: #F8F2E6'></td></tr><tr ID = 'id2736729-67-tr'>PropertiesMineral oil (paraffinic)PolyalphaolefinDialkylated benzenePolyol esterDibasic acid esterPolyglycolPhosphate esterSilicone fluid</tr><tr ID = 'id2736093-86-tr'><td ID = 'id2736095-86-td'>
                                  Viscosity-temperature</td><td ID = 'id2736102-88-td'>
                                  F</td><td ID = 'id2736108-90-td'>
                                  G</td><td ID = 'id2736115-92-td'>
                                  F</td><td ID = 'id2736121-94-td'>
                                  G</td><td ID = 'id2736128-96-td'>
                                  G</td><td ID = 'id2736134-98-td'>
                                  VG</td><td ID = 'id2736141-100-td'>
                                  P</td><td ID = 'id2736147-102-td'>
                                  E</td></tr><tr ID = 'id2736155-105-tr'><td ID = 'id2736157-105-td'>
                                  Low temperature</td><td ID = 'id2736164-107-td'>
                                  P</td><td ID = 'id2736170-109-td'>
                                  G</td><td ID = 'id2736177-111-td'>
                                  G</td><td ID = 'id2736183-113-td'>
                                  G</td><td ID = 'id2736189-115-td'>
                                  G</td><td ID = 'id2736196-117-td'>
                                  G</td><td ID = 'id2736202-119-td'>
                                  F</td><td ID = 'id2736209-121-td'>
                                  G</td></tr><tr ID = 'id2736216-124-tr'><td ID = 'id2736218-124-td'>
                                  High-temperature oxidation stability</td><td ID = 'id2736225-126-td'>
                                  F</td><td ID = 'id2736231-128-td'>
                                  VG</td><td ID = 'id2736237-130-td'>
                                  G</td><td ID = 'id2736244-132-td'>
                                  G</td><td ID = 'id2736250-134-td'>
                                  E</td><td ID = 'id2736257-136-td'>
                                  G</td><td ID = 'id2736263-138-td'>
                                  F</td><td ID = 'id2736269-140-td'>
                                  G</td></tr><tr ID = 'id2736277-143-tr'><td ID = 'id2736279-143-td'>
                                  Compatibility with mineral oil</td><td ID = 'id2736285-145-td'>
                                  E</td><td ID = 'id2736292-147-td'>
                                  E</td><td ID = 'id2736298-149-td'>
                                  E</td><td ID = 'id2736305-151-td'>
                                  G</td><td ID = 'id2736311-153-td'>
                                  F</td><td ID = 'id2736317-155-td'>
                                  P</td><td ID = 'id2736324-157-td'>
                                  P</td><td ID = 'id2736330-159-td'>
                                  P</td></tr><tr ID = 'id2736338-162-tr'><td ID = 'id2736340-162-td'>
                                  Low volatility</td><td ID = 'id2736346-164-td'>
                                  F</td><td ID = 'id2743379-166-td'>
                                  E</td><td ID = 'id2743385-168-td'>
                                  G</td><td ID = 'id2743392-170-td'>
                                  E</td><td ID = 'id2743398-172-td'>
                                  E</td><td ID = 'id2743404-174-td'>
                                  G</td><td ID = 'id2743411-176-td'>
                                  G</td><td ID = 'id2743417-178-td'>
                                  G</td></tr><tr ID = 'id2743425-181-tr'><td ID = 'id2743427-181-td'>
                                  Compatibility with paints and finishes</td><td ID = 'id2743433-183-td'>
                                  E</td><td ID = 'id2743440-185-td'>
                                  E</td><td ID = 'id2743446-187-td'>
                                  E</td><td ID = 'id2743452-189-td'>
                                  P</td><td ID = 'id2743459-191-td'>
                                  P</td><td ID = 'id2743465-193-td'>
                                  G</td><td ID = 'id2743472-195-td'>
                                  P</td><td ID = 'id2743478-197-td'>
                                  VG</td></tr><tr ID = 'id2743486-200-tr'><td ID = 'id2743488-200-td'>
                                  E=excellent; VG=very good; G=good; F=fair; P=poor</td></tr></tbody></table>

No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.