Plumbing the Only Traditional Building System at Mountain Lodge

09/28/2006


Reached only by strenuous hike, LeConte Lodge in Great Smoky Mountains National Park has no electricity but offers other comforts such as hot meals and beds with blankets and clean sheets. Because of 23-year-old storage tanks made with Vipel resin technology available today through AOC, guests also enjoy running water.

At outdoor faucets, guests can fill canteens or splash down after the hike up. Some water is propane-heated to provide washbasin bathing, and the readily available water is essential to food and beverage preparation in the Lodge’s dining hall. However, one of the most welcome amenities running water offers is the availability of flush toilets.

The Lodge water system uses three fiber-reinforced polymer (FRP) composite tanks.The horizontal, aboveground tanks were airlifted by helicopter to the mountaintop in 1983 when the Lodge upgraded its water system and increased capacity 50% by replacing a redwood storage tank.

Virtually maintenance-free

“The composite tanks have been very dependable ever since they were installed,” said Tim Line, General Manager/Owner of the Lodge.“On occasion we’ve wiped off a film that naturally builds on the exterior over time, but that’s about the extent of any tank maintenance we’ve had to do.”

One of the composite units is a 6-ft. diameter, 3,000-gal. holding tank. The other two are 8-ft. diameter, 7,600-gal. supply tanks installed adjacent to one another.

The smaller holding tank is near the mountain’s ever-reliable Basin Spring. Spring water naturally accumulates in three adjacent collector units that feed the holding tank. Gravity-powered water from the holding tank activates the hydraulic ram of a pump that transfers water uphill through piping to the supply tanks. “For every ten gallons of water used to move the ram, one gallon is pumped up to the supply tanks,” Line pointed out. “The other nine gallons end up as Roaring Fork River miles downstream.”

When it is sunny enough, the ram can be activated using solar power. In rare cases when holding tank water levels run low and sunlight is insufficient, a gasoline-powered pump is available for back-up.

To create enough head pressure for good water flow, the two supply tanks are at an elevation higher than lodge facilities. To meet Tennessee State requirements, the water is batch-chlorinated through manholes atop the storage tanks. The Lodge water supply has consistently passed monthly state inspections and quarterly Park Service inspections for water quality.

At the end of the Lodge’s March through November season, the tanks are emptied for the winter when temperatures can drop to -20° F. The tanks also withstand total annual snowfall accumulations that can exceed 60 in., annual rainfall totals that can exceed 70 in., and high winds and debris.

How the tanks were made

The tanks were made by the former Tank Division of Owens Corning who sold the division to Containment Solutions, Inc., in 1995. Tank end caps and cylindrical shells were manufactured using a resin and chopped fiberglass spray-up process. The resin was an isopolyester engineered for potable water use by the Owens Corning Resins & Coatings Division, which became a co-founding partner of AOC.

Each tank has two exterior ribs that allow the tank to be supported by setting the ribs

The ribse shell wall.

To resist ultraviolet degradation, a UV inhibitor was incorporated into the resin for the exterior layers of the tank and ribs. For additional UV protection,

“The proven performance of Vipel resin at LeConte Lodge is a testament to AOC’s corrosion resin technology,” stated Emilio Oramas, AOC Business Manager for the corrosion market.“Today’s Vipel resin technology can offer the same combination of excellent corrosion resistance, structural properties and potable water code recognition.”





No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Learn how to create value with re-use; gain productivity with lean automation and connectivity, and optimize panel design and construction.
Go deep: Automation tackles offshore oil challenges; Ethernet advice; Wireless robotics; Product exclusives; Digital edition exclusives
Lost in the gray scale? How to get effective HMIs; Best practices: Integrate old and new wireless systems; Smart software, networks; Service provider certifications
Fixing PID: Part 2: Tweaking controller strategy; Machine safety networks; Salary survey and career advice; Smart I/O architecture; Product exclusives
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Look at the basics of industrial wireless technologies, wireless concepts, wireless standards, and wireless best practices with Daniel E. Capano of Diversified Technical Services Inc.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.