Pneumatic signaling still wheezes?

Are instrumentation transmitters that use 3-15 psi analog signals still around?

04/08/2011


Dear Control Engineering: I was reading the article about using smart instrumentation, and it discusses some of the history of field devices, back when everything ran on pneumatic systems. Are pneumatic analog devices still around?

Pneumatic devices have been gone for the most part for quite a while, with the majority replaced by the 1980s. Of course their demise was not all in one fell swoop. The move to electronic analog and digital devices took some time and is probably still not entirely complete. Process instrumentation and control devices like valves, that operate on 3-15 psi are certainly still around, but you will have to hunt for them.

After a few minutes digging around the industrial listings on eBay, I managed to find an old Foxboro liquid level transmitter 13FA1-HK31A5 sold by a company called National Recycling. That should tell you something.

There are companies that still sell new 3-15 psi transmitters, but these are rare too. Here’s a company in Italy that still offers a small selection. There are certainly others if you care to look more thoroughly. More often than not, the pneumatic devices available now are converters that change pneumatic to electronic. Here’s one that changes a Foundation fieldbus signal to pneumatic for a control valve.

Suffice it to say, small delicate mechanisms with diaphragms and leak-prone tubing were not exactly maintenance friendly, so I doubt very many people were sad over the change to electronics. As the article points out, compressed air signals can’t convey much information. An air signal line is good for one signal and that’s it. No diagnostic data, no secondary variables, it’s pretty dumb.

Granted there are still folks out there that want to see trains pulled by steam locomotives, cars with carburetors, and their newspapers set on Linotypes, but the romance of such things gets eclipsed quickly when one has to deal with how maintenance intensive those older technologies are.

If you still use pneumatics and are proud of it, let us know.

Peter Welander, pwelander(at)cfemedia.com



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.