Process analyzers

When there is a need to monitor a process variable that extends beyond the “big four” (pressure, flow, temperature, and level), some type of process analyzer usually does the job. And this category of instrumentation has its own big four subtypes: Since manufacturing processes are generally designed for specific functions, the composition or characteristics of a given product should...

12/01/2007


When there is a need to monitor a process variable that extends beyond the “big four” (pressure, flow, temperature, and level), some type of process analyzer usually does the job. And this category of instrumentation has its own big four subtypes:

  • Composition—Detect and measure specific chemical components in the process stream;

  • Electrochemical—Measure specific ion concentration, most commonly hydrogen (pH);

  • Spectrophotometric—Use light absorbing characteristics to detect and measure specific components; and,

  • Physical property—Measure specific gravity, density, viscosity, etc.

Since manufacturing processes are generally designed for specific functions, the composition or characteristics of a given product should fall into relatively narrow bands. For example, while a broad spectrum analyzer that can break down any unknown substance into its component parts may exist in a lab (at least on TV crime dramas), such are not generally practical in a real-life production environment. Gas chromatograph and mass spectrometer devices can quantify a wide range of substances, but their cost and relative complexity make them a choice when simpler technologies can’t do the job.

“Customers ask us about reliability more than accuracy or precision,” says Gary Brewer, product manager for ABB’s process automation division. “Manufacturers don’t usually have large support staffs, so if the analyzer goes down, the whole process can go down. So the rule of thumb is to apply the simplest technology possible that will get the needed measurement.”

When trying to quantify a component or contaminant in a product, it is critical to know what substance you’re looking for. In situations where more than one test has to be performed, more than one analyzer or analyzer technology will likely be involved.

Consider an example where the task is to analyze effluents in flue gas from a boiler, determining quantities of sulfur dioxide (SO 2 ), nitrous oxides (NOx), acid gasses, and mercury. SO 2 can be measured by infrared absorption, non-dispersive infrared, or ultraviolet. For NOx, use chemiluminescence or ultraviolet. Mercury calls for ultraviolet. Acid gasses may require a gas chromatograph or mass spectrometer. Even though ultraviolet may work for three of the four, the situation will likely require more than one sensor, perhaps even a separate sensor for each substance. Multi-component sensors are available, but there are trade-offs with cost and complexity.

Some relatively simple tests, such as pH or dissolved oxygen, can be handled by a probe inserted into a process stream. However, few analysis technologies are this simple. Most involve moving a sample of the product to a device where it can carry out a more complex analytical operation. Analysis becomes, in effect, a batch operation where a sample is extracted from the process stream and checked, just as if it were carried to a lab manually. This process can be automated and happen at appropriate intervals. Methods for designing piping to move samples to the analyzer is another issue. (See article in July Control Engineering .) In some cases to save cost, one device can serve more than one process line, as long as it can handle the span of variables required. Technologies have their own cycle time for analysis. Near infrared is fast enough that it can be essentially continuous, while a gas chromatograph can take 30 minutes to complete a test.

The key to selecting an analyzer, like any piece of instrumentation, is to understand your process and what information is critical to the larger control strategy.



Author Information

Peter Welander is process industries editor. Reach him at PWelander@cfemedia.com .




No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Motor specification guidelines; Understanding multivariable control; Improving a safety instrumented system; 2017 Engineers' Choice Award Winners
Selecting the best controller from several viewpoints; System integrator advice for the IIoT; TSN and real-time Ethernet; Questions to ask when selecting a VFD; Action items for an aging PLC/DCS
Robot advances in connectivity, collaboration, and programming; Advanced process control; Industrial wireless developments; Multiplatform system integration
Motion control advances and solutions can help with machine control, automated control on assembly lines, integration of robotics and automation, and machine safety.
This article collection contains several articles on the Industrial Internet of Things (IIoT) and how it is transforming manufacturing.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Future of oil and gas projects; Reservoir models; The importance of SCADA to oil and gas
Big Data and bigger solutions; Tablet technologies; SCADA developments
SCADA at the junction, Managing risk through maintenance, Moving at the speed of data
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
click me