Radiating cables can solve tricky wireless communication

Leaky feeders can improve communication with moving devices and complex environments.

08/16/2013


Slots in the cable's shielding allow the signal to leak through. Courtesy: ProSoft TechnologyWireless communication depends on antennas to transmit and receive RF (radio frequency) signals. There are many shapes and sizes depending on the nature of the type of transmission and frequency. For this discussion, one useful analogy can be trying to water your garden with a sprinkler.

A central nozzle that sends equal amounts of spray in every direction is like an omni-directional antenna. The signal goes in every direction from a central point. A directional antenna concentrates the signal in a specific direction like a sprinkler that sends out a stream. It can carry a longer distance but covers a smaller area.

A third irrigation technology uses a porous hose that “weeps” water over its length, such that anywhere it runs, water will soak into the ground. The application can be highly controlled by placing the hose in the most critical areas. The same exists in wireless communication where special cable can serve as a continuous antenna over a specific distance, receiving the RF signal as well as transmitting.

Radiating cable is an alternative to traditional RF antenna systems. It solves RF design challenges in certain situations involving moving equipment such as assembly carriers, overhead cranes, and automatic guided vehicles (AGVs). Applications where radiating cable is a consideration include communication in confined spaces, tunnels that snake throughout a process, and large monorail systems requiring consistent RF signal thresholds.

Radiating cable technology, also known as a leaky feeder, has been applied for decades in bi-directional low-frequency radio applications. Highway and railway tunnels commonly use it for emergency radio communication and, more recently, cellular phone connectivity. The technology has also been installed in mines for underground voice radio communications. Now high-speed wireless technologies such as 802.11n with fast roaming may benefit from radiating cable systems, thus extending automation networks to moving equipment.

Radiating cable is similar to standard discrete antennas in many ways. RF energy is sent through the cable and the signal propagates out. Radiating cable, however, does not have gain. As the cable gets longer, the signal gets weaker. Slots in the shield part of the coax, underneath the insulation, allow the RF signal to propagate out and be received along the length of the cable. This effectively creates a long, flexible RF antenna at over 100 m in length.

There are limitations when compared with more conventional antennas. Radiating cable reduces available bandwidth, so 802.11n performance is slower as compared to a multi-stream MIMO antenna system. The cable itself and all the necessary mounting hardware can make for higher material costs and more complex installation. So, in most industrial wireless applications, traditional discrete antennas are recommended unless they are not capable of reliable radio links due to confined spaces or line-of-sight challenges. But where traditional antennas are not practical, radiating cable is a good alternative to investigate.

Jim Ralston and Gary Enstad are product strategy managers for ProSoft Technology.

www.prosoft-technology.com

Read more on industrial wireless coverage at www.controleng.com/wireless



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.