Radio frequency basics

Industrial wireless tutorials: Any radio frequency (RF) discussion quickly expands to the entire technology surrounding the generation and propagation of a radio signal or wave. Here’s what you need to know.


Industrial Wireless Tutorials – a new Control Engineering blogAny radio frequency (RF) discussion quickly expands to the entire technology surrounding the generation and propagation of a radio signal, or wave. A radio wave is an electromagnetic phenomenon like sound* and light. Radio waves act more like light than sound, however; RF travels at the speed of light. The overall range of radio spectrum is 3 kHz to 300 GHz.

Radio waves are defined by several parameters. The first is the wavelength, which is defined as the distance between two identical points on successive waves. This can be peak to successive peak or trough to trough. Wavelength is measured in meters or millimeters. A wave also has a frequency. The frequency of any wave is the amount of 360-deg cycles completed within a given time; a cycle consists of a positive and negative half, both beginning and ending at zero amplitude. Frequency is measured in Hertz (named after Heinrich Hertz); 1 Hertz is one cycle per second. Amplitude is a measure of the strength of the wave or the peak value of the wave. The amplitude depends on the type or power of the transmitter. 

Power measurements

Power is measured using different values. Some are absolute values while others are relative. A common unit used is the decibel. The decibel (dB) is a measure of relative power; two values are compared to one another and the relative change is calculated. On the other hand, the Watt (W), milliwatt (MW), and dBm (decibels referenced to 1 MW) are units of absolute power measurement and are referenced either to zero or to a fixed reference. A typical Wi-Fi transmitter has an output of 20 dBm, which corresponds to 100 MW.

To propagate a radio wave, a transmitter is used to produce the carrier signal, which is the signal centered at the transmitter's assigned frequency The carrier is modulated and amplified by any one of the common methods available and then applied to an antenna, which produces an electromagnetic wave in space. The wave has both an electrical and a magnetic component, which travel the same path at right angles to one another. Modulation is the means by which usable information is impressed upon the carrier wave. Before being modulated, the carrier is a pure sine wave; afterward, the impressed information causes the wave to vary around the carrier frequency within a fixed range of frequencies, called the bandwidth. Note that the term bandwidth, as used with data communication, means the theoretical throughput of the channel; this is related directly to the width of the channel.

For comparison, amplitude modulation (AM) transmissions have a bandwidth of 10 kHz (kilohertz, or 1000 cycles per second) because the usable dynamic range of the impressed intelligence is 5 kHz, the range of AM receivers. If the carrier is 1000 kHz, then the bandwidth is +/- 5 kHz around the carrier at 100% modulation, from 995 to 1005 kHz. Channels must be separated by 10 kHz to avoid interfering with adjacent channels. 

Bandwidth explanation

Bandwidth is an important concept in understanding Wi-Fi technology. To avoid interference with other users, Wi-Fi channels are restricted to either 20 or 22 MHz wide channels. This has the effect of protecting adjacent information channels from the corruption resulting from interference. The downside is that bandwidth has the effect of limiting data throughput. This has been addressed in the latest amendments to the IEEE 802.11 standard.

Daniel E. Capano, owner and president, Diversified Technical Services Inc. of Stamford, Conn., is a certified wireless network administrator (CWNA) and writes posts for the Control Engineering blog, Industrial Wireless Tutorials.Beginning in IEEE 802.11n, a technique known as channel bonding will be used to allow the combining, or bonding, of multiple 20 MHz channels, up to a maximum of 8 channels bonded to provide a 160 MHz channel. This, coupled with up to eight radios, will allow wireless throughputs approaching 7 Gbps.

- Daniel E. Capano, owner and president, Diversified Technical Services Inc. of Stamford, Conn., is a certified wireless network administrator (CWNA). Edited by Mark T. Hoske, content manager, CFE Media, Control Engineering,

ONLINE extras has other wireless tutorials from Capano. has wireless webcasts, some for PDH credit.

Control Engineering has a wireless page


*Reader feedback

Joe Keesey, control system engineer, DuPont for 35 years, now retired, sent a July 27 email about the above post (also appearing in July Control Engineering, p. 20). He noted that sound is mechanical, based on vibrations, following a different set of physical rules than radio and light waves.

Dan Capano, in reply, agreed that sound is mechanical rather than electromagnetic, explaining, "The point was that sound also is a periodic function; the analogy is illustrative."

CHRISTOPHER , Non-US/Not Applicable, United Kingdom, 07/10/14 11:30 AM:

100 MW!
that's a power station
mW more like
Anonymous , 07/10/14 12:17 PM:

Uh, sound is not electromagnetic in nature.
Anonymous , 07/10/14 12:48 PM:

Great tutorial, thank you. Just one comment - mW means milliwatt, and MW means megawatt.
ROBERT , CA, United States, 07/10/14 04:56 PM:

Good, sound basic explanation of RF Energy.
I would still prefer to return to the days of Kilocycles (Kc) and Megacycles (Mc) as this is descriptive of the actual nature of an electromagnetic wave......Although it may have seemed a nice sentimental reason to adopt "Hertz" why make it more "abstract" than it has to be. Kc. & Mc. are technically descriptive......Hertz is a "rent-a-car". :-)
Miroslaw , Non-US/Not Applicable, Poland, 07/11/14 07:17 AM:

MW means Mega Watt
milliwatt is mW
Mark , NE, United States, 07/15/14 04:16 PM:

Two corrections:

1) Sound is not an electromagnetic (EM) phenomenon. It is converted to EM for transmission from the source to a speaker. Sound is a mechanical pressure wave through a medium such as air or water.

2) The correct abbreviation for milliwatts is mW. MW is the abbreviation for megawatts which is one million Watts.
Phil , Quebec, Canada, 07/22/14 09:41 AM:

Very helpful - thanks!
STEPHEN , VA, United States, 08/09/14 01:42 PM:

Heh, heh to the Hertz haters. Would you say the same about Volts, Amperes and Ohms? The 1960s are passed. Get over it.
SAL , SC, United States, 08/15/14 09:00 AM:

Very good information in simple language. Please keep posting this type of information for the sake of knowledge spreading.
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Additive manufacturing benefits; HMI and sensor tips; System integrator advice; Innovations from the industry
Robotic safety, collaboration, standards; DCS migration tips; IT/OT convergence; 2017 Control Engineering Salary and Career Survey
Integrated mobility; Artificial intelligence; Predictive motion control; Sensors and control system inputs; Asset Management; Cybersecurity
Featured articles highlight technologies that enable the Industrial Internet of Things, IIoT-related products and strategies to get data more easily to the user.
This article collection contains several articles on how automation and controls are helping human-machine interface (HMI) hardware and software advance.
This digital report will explore several aspects of how IIoT will transform manufacturing in the coming years.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Mobility as the means to offshore innovation; Preventing another Deepwater Horizon; ROVs as subsea robots; SCADA and the radio spectrum
Future of oil and gas projects; Reservoir models; The importance of SCADA to oil and gas
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me