Research: Wireless use in industry

What wireless technologies are being used for industrial applications? IEEE 802.11, Bluetooth, and wireless are widely used. More information is being gathered.

03/20/2013


Figure shows wireless networks used for industrial applications. For 2013, information is being gathered on individual protocols. Courtesy: IMS Research (Part of IHS Inc.)Wireless in industrial applications has been around for a number of years. Its use has mainly been in areas where a traditional networking solution of industrial Ethernet or fieldbus has not been feasible, either through problems with distance, cost, or lack of existing infrastructure. Wireless technology has had to overcome a number of barriers in the past: A perceived lack of reliability, its suitability for control, and its ability to transmit in a busy environment have all hindered its adoption. However, as the technology has matured, user acceptance has grown.

Wireless communications used in factory and process automation are currently driven by three main technologies. In 2011, IHS estimated that almost one quarter of all new wireless connections made were made by wireless LAN. This can be in the form of 802.11a, b, g, and n. Modes a, b, and g are more popular, but n mode is beginning to make headway as it moves from the consumer market into the industrial space. Common use of multiple antennae means it has built-in redundancy should a single antenna be damaged or fail.

Bluetooth is also widely used within industry and is estimated to account for over one-fifth of total new wireless connections in 2011. Classic Bluetooth is relatively low bandwidth, but the newer Bluetooth high-speed variant is designed to improve this. Bluetooth can be suitable for battery-powered solutions, although Bluetooth Low Energy has been designed specifically with this in mind.

Cellular technology has been in used in wireless communication for some time now and is estimated to make up 15% of new connections. It is very suitable for long-distance transmission due to the existing cellular infrastructure in remote locations. This makes it very suitable for SCADA systems.

Many proprietary and “other” solutions exist in the wireless space. These include unlicensed bands such as the sub-GHz range as well as long haul communications. These are popular in the process industry and, like most wireless solutions, do not require any existing network infrastructure. The lower cost of installation can make them an appealing prospect to those looking to install wireless. WirelessHART and ISA100.11a have, until recently, been working toward a single standard. This, however, has not been successful and is unlikely to occur in the near future. The lack of convergence means these two technologies will continue to vie for new connections in the industrial space.

- Tom Moore, B.Sc, is analyst for industrial automation, IMS Research (Part of IHS Inc.). Edited by Mark T. Hoske, content manager, CFE Media, Control Engineering and Plant Engineering, mhoske(at)cfemedia.com.

ONLINE

IMS Research (IHS) July 2013 wireless networking report link 

www.imsresearch.com 

www.ihs.com  



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Learn how to create value with re-use; gain productivity with lean automation and connectivity, and optimize panel design and construction.
Go deep: Automation tackles offshore oil challenges; Ethernet advice; Wireless robotics; Product exclusives; Digital edition exclusives
Lost in the gray scale? How to get effective HMIs; Best practices: Integrate old and new wireless systems; Smart software, networks; Service provider certifications
Fixing PID: Part 2: Tweaking controller strategy; Machine safety networks; Salary survey and career advice; Smart I/O architecture; Product exclusives
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Look at the basics of industrial wireless technologies, wireless concepts, wireless standards, and wireless best practices with Daniel E. Capano of Diversified Technical Services Inc.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.