Safety hike after Yellowstone burst

Exxon Mobil took twice as long as it said it did to fully seal a pipeline that spilled 1,000 barrels of crude oil into the Yellowstone River, according to federal documents.

07/11/2011


Exxon Mobil tISS Sourceook twice as long as it said it did to fully seal a pipeline that spilled 1,000 barrels of crude oil into the Yellowstone River, according to federal documents.

Details about the company’s response to the Montana pipeline rupture came to light this week. The Department of Transportation (DOT) ordered the company to bury the duct deeper beneath the riverbed, where they buried it 5 to 8 ft underground to deliver 40,000 barrels of oil a day to a refinery in Billings.

Records show Exxon did not seal the pipeline until 56 minutes after the break occurred Friday near Laurel. That’s longer than the 30 minutes company officials said in a briefing Tuesday with federal officials and Gov. Brian Schweitzer.

An Exxon Mobil spokesman said the longer time span came from information provided to the agency by the company and the discrepancy might have come about because Exxon Mobil Pipeline Co. President Gary Pruessing was speaking without any notes in front of him when he addressed Schweitzer.

“Clearly our communication with the regulator (DOT) is the one that we’ve got precision on,” spokesman Alan Jeffers said.

It was not the first time the company offered clarification of its response and assessment of the spill. A day earlier, the company acknowledged under political pressure the leak’s impact could extend far beyond a 10-mi stretch of the river it initially said was the most affected area. The company had earlier downplayed government officials’ assertions damage spread over dozens of miles.

The waterway rose above flood stage Tuesday which raised fears that surging currents could push crude into undamaged areas and back channels vital to the river’s prized fishery. Conditions have also hampered efforts to find the cause of the break.

The river has been flowing too swiftly for crews to reach some oiled areas, and forecasters said mountain snowmelt was adding to high water levels. Officials said the surge may push oil into areas that have not suffered damage yet.

Transportation officials said Tuesday oil was as far downstream as 240 mi in Terry, Mont. The agency said Exxon Mobil provided that information, but company spokesman Alan Jeffers said he was not aware of any such sighting.

Exxon planned to test the river’s conditions with a jet boat, with eight more on standby if the launch is successful, Glass said.

Federal regulators have ordered Exxon to make safety improvements to the 20-yr-old pipeline. Among them was an order to re-bury the line to protect against external damage and assess risk where it crosses a waterway, which the company intended to comply with, Jeffers said.

The company also will have to submit a restart plan to the DOT before crude can again flow through the line.

Schweitzer also ordered a review of pipelines that cross major and minor rivers in the state. Officials will look at the pipes’ age, location of shut-off valves and whether they are similar to the ruptured pipe. He said the state has 88 such crossings.

Modern pipelines can be buried as much as 25 feet beneath bodies of water; Exxon Mobil’s Silvertip line was 5 to 8 ft below the bottom of the Yellowstone.

- Edited by Amanda McLeman, Plant Engineering, www.plantengineering.com



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Learn how to create value with re-use; gain productivity with lean automation and connectivity, and optimize panel design and construction.
Go deep: Automation tackles offshore oil challenges; Ethernet advice; Wireless robotics; Product exclusives; Digital edition exclusives
Lost in the gray scale? How to get effective HMIs; Best practices: Integrate old and new wireless systems; Smart software, networks; Service provider certifications
Fixing PID: Part 2: Tweaking controller strategy; Machine safety networks; Salary survey and career advice; Smart I/O architecture; Product exclusives
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Look at the basics of industrial wireless technologies, wireless concepts, wireless standards, and wireless best practices with Daniel E. Capano of Diversified Technical Services Inc.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.