Sandia National Laboratories Molten Salt Test Loop

New Construction; Sandia National Laboratories Molten Salt Test Loop; Bridgers & Paxton Consulting Engineers Inc.


Sandia mechanical technologist John Kelton sifts through a bucket of salt beads. Courtesy: Bridgers + Paxton Consulting EngineersEngineering firm: Bridgers & Paxton Consulting Engineers Inc.
2013 MEP Giants rank:
Sandia National Laboratories Molten Salt Test Loop
Albuquerque, N.M., United States
Building type:
Project type:
New construction
Engineering services:
Automation & Controls, Code Compliance, Electrical/Power, HVAC, Lighting
Project timeline:
April 2010 to July 2012
Engineering services budget:
MEP budget: $8.43 million


The Molten Salt Test Loop (MSTL) project is a first-of-a-kind concentrated solar power (CSP) power plant test facility that allows manufacturers and university research facilities around the world to come to Sandia National Laboratories to perform accelerated lifecycle tests of power plant size components in flowing molten nitrate salt. There are currently no facilities in the world MSTL furnace and pumps. Courtesy: Bridgers + Paxton Consulting Engineerscapable of performing accelerated lifecycle testing of power plant size components in a 585 C (1085 F) high temperature molten nitrate salt environment.

The objective of the MSTL project was to advance solar energy application technology in the power generation arena beyond any current existing low temperature technology. The completed test platform allows a variety of actual power plant size components to be tested to support the ultimate goal of large scale solar electrical generation. The MSTL at Sandia National Laboratories' National Solar Thermal Test Facility (NSTTF) was designed by Bridgers & Paxton Consulting Engineers, Inc., to provide three parallel test platforms for the performance and evaluation of concentrating solar collectors and power plant size components in flowing molten nitrate salt simulating solar power plant conditions.

A key characteristic of CSP is its built-in thermal inertia, which provides stability in power plant output during Salt cooler and test control building. Courtesy: Bridgers + Paxton Consulting Engineers changes in solar radiation, such as when clouds pass over. This technology consists of pumping molten salt through various types of solar collectors such as parabolic troughs, linear Fresnel, or elevated tower receivers. These technologies involve converting sunlight into thermal energy for use in a heat-driven turbine engine for generating electrical power. In a functioning test loop, mirrors are used to track the sun and focus concentrated solar energy onto solar collectors, which contain circulating molten salt. The molten salt is an excellent energy storage media, which can then be collected in large storage vessels (>500k gal tanks) for later use to generate electrical power. This energy can be stored well into the night and generate power when needed. The potential CSP generating capacity in the United States is 7,500 gigawatts (GW), which is several times greater than the entire U.S. electrical grid capacity. During an assumed lifetime of 30 years, a CSP system would produce about 20 times the energy required for its manufacture while significantly reducing greenhouse gas emissions and reliance on fossil fuel power generation.

Site photo. Courtesy: Bridgers + Paxton Consulting EngineersSolutions

This one-of-a-kind structure required components that were not manufactured in the United States, due the unique materials necessary to flow molten salt at high temperatures. This required a great deal of research and communication with various companies around the world to identify companies that could meet the owner's requirements. Molten salt is very corrosive at high temperatures and will permeate through valve packing material. B&P's design approach took into consideration Sandia's requirement to design this testing facility for a 20-year operational life; in doing so, B&P took great care in specifying materials that would handle extreme temperature cycling, pressure cycling, and extreme corrosive environments. The design also included numerous design approaches that could handle three major types of failures in order to prevent salt freeze up within the system. These approaches included: positive drain back to salt furnace during particular power outage events, redundant heat trace capability, and a unique Closeup of Test Loop 3. Courtesy: Bridgers + Paxton Consulting Engineersapproach to piping insulation which accounts for piping expansion and contraction while maintaining a high level of insulation efficiency.

An additional example of an innovative technique is that B&P's design mechanically controls the temperature of the extended valve bonnet to maintain it at 275 C while salt flows through the valve at 585 C (1085 F). This unique design approach will substantially extend the life of the valve bonnet packing material and reduce downtime for maintenance. Challenges included 16 months for the pump manufacturer to design and build the 9-stage vertical turbine pump, which ultimately weighed 14,500 lbs. and was 26 ft in height. Another challenge was the complex piping design, which accounted for thermal expansion and thermal cycling of the piping test loops and required a unique design approach. B&P’s approach to the analysis was to neutralize movement and mechanical loads at the three test loop/customer interface connection points and subsequently protect the resident equipment. Included in the objective was maintaining a robust hard pipe system, avoiding the use of any flexible expansion compensation devices. To meet the objective, the pipe needed to be fully restrained at the interface points by restricting movement in all 6 degrees of freedom (3 translational and 3 rotational axes); however, restricting movement comes with limitations.

No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.