Soft starter designs, functions

High inrush currents and mechanical wear and tear are two principal causes of motor damage. Drives can protect attached mechanical components from wear and tear by slowly starting and stopping the drive train. When a variable speed drive isn’t an option, a soft starter can ease the initial impact of the motor starting and soften the blow when it shuts off. Back to Basics, June 2008

06/01/2008


High inrush currents and mechanical wear and tear are two principal causes of motor damage. Drives can protect attached mechanical components from wear and tear by slowly starting and stopping the drive train. When a variable speed drive isn’t an option, a soft starter can ease the initial impact of the motor starting and soften the blow when it shuts off.

 

Soft starters are especially useful for conveyors, fans, pumps, and any equipment where starting or stopping at full speed applies too much stress or could damage the product being moved by the machine. Other motor-driven applications where soft starters can provide benefit include escalators and moving walkways in jurisdictions where such devices can automatically stop and start as needed to save energy.

 

How do soft starters work?

Instead of applying the full voltage available to start the motor when powered on, a soft starter ramps up the voltage according to the application.

 

Douglas Yates, product manager, MCG Products, North America Motion Controls, Danfoss Inc., says that while a variable speed drive, as the name suggests, changes motor speed, a soft starter cannot. Inside, he says, a pattern of solid-state switches—called silicon-controlled rectifiers (SCRs) or thyristors—open in different intervals for voltage to ramp up to full speed.

 

SCR-diode and SCR-SCR designs are available for three-phase motor applications. SCR-diode requires higher start current, causes more heat, and generates undesirable harmonics, Yates says; SCR-SCR provides full wave control.

 

Motion Control, Power Controls

Current feedback loops hellp protect the motor and provide other current-based functions.

Designs, by phase, open, closed

 

Designs vary further by phase and whether they open or close the control loop, Yates explains:

 

  • Single-phase units control start torque, but do not reduce start current. Therefore, they are inadequate for applications with frequent cycling or high inertia loads;

  • Two-phase units do not isolate all phases from the motor. This type of control requires a thermal relay or circuit breaker to protect the motor;

  • Three-phase units provide full control of all three phases, giving maximum control of current and torque;

  • Open-loop designs offer no current feedback loop. They control starting with a preselected voltage profile, and do not provide motor protection; and

  • Closed-loop designs (diagram) provide motor protection and other current functions, and allow the user to set a maximum start current level.

Features, advances

Recent soft starter advances include:

 

  • Smaller (solid-state) electronics or silicon-controlled rectifiers have allowed for smaller dimensions, making use easier for machine and panel builders;

  • Wide variety of currents and voltages are available (with wider voltage ranges available in specific models);

  • Better sensors for protection and diagnostics help eliminate nuisance trips;

  • Presets appropriate to various applications’ starting curves or torque ramping needs;

  • Options for closed loop control or operator indication are available, with signal relays included with some models;

  • Easier settings with knobs (no programming required);

  • Wider communications availability;

  • More mounting, enclosure, and high voltage safety interlock options; and

  • Multiple certifications and approvals.

 

www.danfossdrives.com

 

 

Author Information

Mark T. Hoske is editor in chief, Control Engineering. Reach him at MHoske@cfemedia.com .

 



No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
Detecting security breaches: Forensic invenstigations depend on knowing your networks inside and out; Wireless workers; Opening robotic control; Product exclusive: Robust encoders
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide
 

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.