Terminology in Motion

Motion control, as other technologies, has its fair share of special terms. Not all of them are rigorously defined; some require blending to suit the specific audience. Here's a sampling of some well-known and not-so-well-known terms.A motion control system typically consists of a controller to process motion algorithms and signals; an amplifier to boost signals to a level needed to p...

01/01/1998


Motion control, as other technologies, has its fair share of special terms. Not all of them are rigorously defined; some require blending to suit the specific audience. Here's a sampling of some well-known and not-so-well-known terms.

A motion control system typically consists of a controller to process motion algorithms and signals; an amplifier to boost signals to a level needed to power an actuator that provides the motion output; and feedback (sensors/transducers) to allow adjustments for process changes, based on comparing measured output with the input.

An operator interface or host terminal front-end completes the system. Feedback implies that most motion control systems operate in closed-loop ; however, some run in open-loop , notably a step-motor-based system. Actuators come in various forms—motors, cylinders, solenoids, etc.—and can be electric, hydraulic, pneumatic, or other type.

Axis —Any movable part of a machine or system that requires controlled motion. Several axes of motion can be combined in a coordinated multiaxis system.

Circular interpolation —Coordination of two independent motion axes to produce an apparent circular motion. It's done through a series of straight line approximations via software algorithms.

Commutation —Sequential excitation of motor windings to maintain the relative phase angle between the rotor and stator magnetic fields, within specified limits, to control motor output. In brush dc motors, this function is accomplished by a mechanical commutator and carbon brushes; in brushless motors, it's done electronically using rotor position feedback.

Electronic gearing —A method that simulates mechanical gears by electrically "slaving" one closed-loop axis to a second axis (open- or closed-loop) through a variable ratio.

Encoder —A feedback device that translates mechanical motion into electrical signals indicative of actuator position. Incremental and absolute encoders are common varieties; as the names imply, their output indicates incremental or absolute changes of position.

Feedforward —A method that "precompensates" a control loop for known errors due to motor, drive, or load characteristics to improve response. It depends only on the command, not the measured error.

Indexer —An electronic unit that converts high-level commands from a host computer, PLC, or operator panel into step and direction pulses needed by a stepping motor driver.

Loop bandwidth —Maximum rate at which a control loop can respond to a change in a control parameter. It's indicative of loop performance and is expressed in Hertz (Hz).

Motion profile —The velocity versus time (or position) relationship of the move made by a motion axis. See diagram for two common, though unrelated, types of motion profiles.

Overshoot —A system response where the output or result exceeds the desired value.

Pulse-width modulation —A switch-mode control method used in amplifiers and drivers to control motor voltage and current to obtain higher efficiency than linear control. PWM refers to variable on/off times (or width) of the voltage pulses applied to the transistors.

Quadrature —A technique that separates signal channels by 908 (electrical) in feedback devices. It is used with encoders and resolvers to detect direction of motion.

Resolver —A position transducer that uses magnetic coupling to measure absolute shaft position during one revolution.

Servo mechanism —An automatic, closed-loop motion control system that uses feedback to control a desired output such as position, velocity, or acceleration.

Tachometer —An electromagnetic feedback transducer providing an analog voltage signal proportional to rotational speed.

This sampling of terms draws on various sources, notably, Programmable Motion Control Handbook (1992) , National Electrical Manufacturers Association (Washington).





No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
The Engineering Leaders Under 40 program identifies and gives recognition to young engineers who...
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Learn how to create value with re-use; gain productivity with lean automation and connectivity, and optimize panel design and construction.
Go deep: Automation tackles offshore oil challenges; Ethernet advice; Wireless robotics; Product exclusives; Digital edition exclusives
Lost in the gray scale? How to get effective HMIs; Best practices: Integrate old and new wireless systems; Smart software, networks; Service provider certifications
Fixing PID: Part 2: Tweaking controller strategy; Machine safety networks; Salary survey and career advice; Smart I/O architecture; Product exclusives
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Look at the basics of industrial wireless technologies, wireless concepts, wireless standards, and wireless best practices with Daniel E. Capano of Diversified Technical Services Inc.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.