Understanding differential pressure flowmeters

Traditional flow measurement technique survives and thrives, often updated with current technology.


Trying to force the fluid through an orifice creates a pressure drop in proportion to the flow rate.When a flow measurement technique that has been around since the automation dark ages continues to show among the top performing technologies, it indicates a high level of reliability, versatility, and adaptability. Such is the case with differential pressure flowmeters. As a flow metering technique, it consistently ranks among the top five.

This is really a very large family of designs that separates into two main categories: flow obstructions and Pitot tubes. For purposes of this discussion, we’ll consider only the former. When an obstruction is placed in a pipe, there will be a difference in fluid pressure upstream and downstream from the obstruction. This difference can be measured and characterized to provide the basis for calculating flow. (An electrical parallel is calculating amperage by measuring the voltage drop across a known resistance.) While it may not be the first flow measuring technique invented, it is certainly one of the earliest, and quickly followed the first practical pressure gages.

Understanding the concepts of a magnetic or Coriolis flowmeter may stretch your thinking but differential pressure flow measurement mechanics are easy to grasp (although the actual equations can get pretty complicated). This familiarity, combined with its simplicity, helps the technology survive. The most basic implementation involves placing a disk or other type of orifice in a pipe with an opening smaller than the pipe’s inner diameter, and then taking a differential pressure measurement comparing the up- and down-stream sides of the orifice. There are many practical advantages to this approach:

• The technology is simple and easy to understand;
• There are no moving parts;
• The sensor is very compact;
• Works equally well for gas or liquid;
• Can be configured to measure bi-directional flow;
• Usable over a very wide range of sizes;
• Devices can be mechanical or electronic;
• Relatively inexpensive; and,
• You can even build one yourself. (Watch a video demonstration.)

Since this approach uses a pressure sensor, suppliers have included all the technological advances of those product families as part of the package. There are some very sophisticated units available, and those improvements carry over to the flowmeter application. These can provide diagnostic information and multiple variables.

On the other hand, there are some drawbacks:

• It’s not the most accurate flow measurement technology. If high precision or wide turn-down ability is a key objective, there are better choices.
• Devices cause a pressure drop and reduce the pipe’s free passage. The extent of this depends on the design.
• Accuracy and turn-down are related to pressure drop. The more accuracy and range you need, the greater pressure drop you will have to tolerate.
• While there are no moving parts, the orifice itself is often a wear-prone point. If it gradually enlarges, the flow measurement will read proportionally lower. On the other hand, if it becomes partly obstructed with debris, the measurement will read higher.
• The same application and installation guidelines for pressure sensors apply here. Anything that interferes with the pressure readings (clogged impulse lines, etc.) will interfere with a true flow calculation.
• Changes in liquid characteristics (viscosity, multiphase flow, etc.) can affect readings. This varies by design.
• These are generalities, so discuss your specific application needs with any prospective suppliers.

Differential pressure flowmeters are available from a variety of suppliers. A search on “differential pressure flowmeter” at www.controleng.com turned up more than 350 results.

Peter Welander, pwelander@cfemedia.com

SWAPAN , Non-US/Not Applicable, India, 12/20/13 12:03 AM:

If use of the flow element has bottleness or pressure nipples get choked, the flow measurement using dp type flow transmitter becomes fruitless or gives erroneous readings with time. as mentioned in the article. In that case, please advice any alternative means for flow measurement in steam, water or important fluid applications normally used in thermal power plants .
Makarand , Australia, 12/23/13 05:32 PM:

You have correctly pointed out, DP Flow Meters are suitable for clean and non congealing type process fluid. For steam services Orifice, Annubar and flow nozzles are established primary elements and work well. For services that block the tappings you can use Remote Diaphragm seals upto 300 Deg C!
RYSZARD , AL, Poland, 01/20/14 02:48 AM:

The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
Each year, a panel of Control Engineering editors and industry expert judges select the System Integrator of the Year Award winners.
Control Engineering Leaders Under 40 identifies and gives recognition to young engineers who...
Learn more about methods used to ensure that the integration between the safety system and the process control...
Adding industrial toughness and reliability to Ethernet eGuide
Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving
Big plans for small nuclear reactors: Simpler, safer control designs; Smarter manufacturing; Industrial cloud; Mobile HMI; Controls convergence
Virtualization advice: 4 ways splitting servers can help manufacturing; Efficient motion controls; Fill the brain drain; Learn from the HART Plant of the Year
Two sides to process safety: Combining human and technical factors in your program; Preparing HMI graphics for migrations; Mechatronics and safety; Engineers' Choice Awards
The Ask Control Engineering blog covers all aspects of automation, including motors, drives, sensors, motion control, machine control, and embedded systems.
Join this ongoing discussion of machine guarding topics, including solutions assessments, regulatory compliance, gap analysis...
News and comments from Control Engineering process industries editor, Peter Welander.
IMS Research, recently acquired by IHS Inc., is a leading independent supplier of market research and consultancy to the global electronics industry.
This is a blog from the trenches – written by engineers who are implementing and upgrading control systems every day across every industry.
Anthony Baker is a fictitious aggregation of experts from Callisto Integration, providing manufacturing consulting and systems integration.
Integrator Guide

Integrator Guide

Search the online Automation Integrator Guide

Create New Listing

Visit the System Integrators page to view past winners of Control Engineering's System Integrator of the Year Award and learn how to enter the competition. You will also find more information on system integrators and Control System Integrators Association.

Case Study Database

Case Study Database

Get more exposure for your case study by uploading it to the Control Engineering case study database, where end-users can identify relevant solutions and explore what the experts are doing to effectively implement a variety of technology and productivity related projects.

These case studies provide examples of how knowledgeable solution providers have used technology, processes and people to create effective and successful implementations in real-world situations. Case studies can be completed by filling out a simple online form where you can outline the project title, abstract, and full story in 1500 words or less; upload photos, videos and a logo.

Click here to visit the Case Study Database and upload your case study.