Energy, Power

Efficient boiling research for power plants to improve energy efficiency

MIT research is looking to develop understanding of heat transfer in boiling water, which could lead to efficiency improvements in power plants and improved analytics.
By David L. Chandler April 5, 2019
Image shows the rate of heat transfer from a metal surface, with red the highest and blue the lowest. The large blue areas show the beginning of a boiling crisis. Courtesy: Massachusetts Institute of Technology (MIT)

MIT research may lead to ways for more efficient boiling water heat transfer, which could improve energy efficiency for power plants, boiler control and various manufacturing processes. In part, more sensitive instrumentation is helping with analytics.

This analysis could help resolve one of the thorniest problems facing heat exchangers and other technologies in which boiling water plays a central role: how to predict, and prevent, a dangerous and potentially catastrophic event called a boiling crisis. This is the point when so many bubbles form on a hot surface that they coalesce into a continuous sheet of vapor that blocks any further heat transfer from the surface to the water.

Such events can cause weakening or melting, so nuclear plants are designed to operate at levels far below those that could trigger a boiling crisis. This new understanding might allow such plants to operate safely at higher output levels by reducing the needed operating margins.

“It’s a very complex phenomenon,” said Matteo Bucci, assistant professor of nuclear engineering at MIT. And although it has been “studied for over a century, it’s still very controversial.” Even in the 21st century, he said, “We talk about an energy revolution, a computer revolution, nanoscale transistors, all kinds of great things. Yet, still in this century, and maybe even in the next century, these are all limited by heat transfer.”

As computer chips get smaller and more powerful, for example, some high-performance processors may require liquid cooling to dissipate heat that can be too intense for ordinary cooling fans. Likewise, the power plants that produce most of the world’s electricity, whether they be fossil fuel, solar, or nuclear plants, mainly produce power by generating steam to turn turbines.

In a nuclear plant, water is heated by the fuel rods, which heat up through nuclear reactions. The spread of heat through the metal surfaces to the water is responsible for transferring energy from the fuel to the generating turbine, but it also is key to preventing the fuel from overheating and potentially leading to a meltdown. In the case of a boiling crisis, the formation of a layer of vapor separating the liquid from the metal can prevent the heat from being transferred, and can lead to rapid overheating.

Because of that risk, regulations require nuclear plants to operate at heat fluxes that are no more than 75% of the level known as the critical heat flux (CHF), which is the level when a boiling crisis could be triggered that could damage critical components. But since the theoretical foundations of the CHF are poorly understood, those levels are estimated very conservatively. It’s possible that those plants could be operated at higher heat levels, thus producing more power from the same nuclear fuel, if the phenomenon is understood with greater certainty, Bucci said.

A better understanding of boiling and the CHF is “such a difficult problem because it is very nonlinear,” and small changes in materials or surface textures can have large effects, Bucci said. But now, thanks to better instruments able to capture details of the process in lab experiments, “we have been able to actually measure and chart the phenomenon with the required spatial and temporal resolution” to be able to understand how a boiling crisis gets started in the first place.

It turns out the phenomenon is closely related to the flow of traffic in a city, or to the way an outbreak of disease spreads through a population. Essentially, it’s an issue of the way things clump together.

When the number of cars in a city reaches a certain threshold, there is a greater likelihood that they will bunch up in certain places and cause a traffic jam. And, when carriers of disease enter crowded places like airports or auditoriums, the chances of triggering an epidemic are increased. The researchers found that the population of bubbles on a heated surface follows a similar pattern; above a certain bubble density, the likelihood goes up that bubbles will crowd together, merge, and form an insulating layer on that surface.

“The boiling crisis is essentially the result of an accumulation of bubbles that merge and coalesce with each other, which leads to failure of the surface,” Bucci said.

Because of the similarities, Bucci said, “We can take inspiration, take the same approach to model boiling as is used to model traffic jams,” and those models have already been well-explored. Now, based on both experiments and mathematical analysis, Bucci and his researchers have been able to quantify the phenomenon and arrive at better ways to pin down when the onset of such bubble mergers will take place. “We showed that using this paradigm, we can predict when the boiling crisis will occur,” based on the patterns and density of bubbles that are forming.

Image shows the rate of heat transfer from a metal surface, with red the highest and blue the lowest. The large blue areas show the beginning of a boiling crisis. Courtesy: Massachusetts Institute of Technology (MIT)

Image shows the rate of heat transfer from a metal surface, with red the highest and blue the lowest. The large blue areas show the beginning of a boiling crisis. Courtesy: Massachusetts Institute of Technology (MIT)

The nanoscale texture of the surface plays an important role, the analysis shows, and that’s one of several factors that might be used to make adjustments that could raise the CHF, and thus potentially lead to more reliable heat transfer, whether for power plants, liquid cooling for advanced computer chips, or many other processes where heat transfer is a crucial factor.

“We can use this information not only to predict the boiling crisis, but also to explore solutions, by changing the boiling surface, to minimize the interaction between bubbles,” Bucci said. “We’re using this understanding to improve the surface, so we can control and avoid the ‘bubble jam.’”

If this research enables changes that could allow for safe operation of nuclear plants at higher heat fluxes — that is, the rate at which they dissipate heat — than currently allowed, the impact could be significant. “If you can show that by manipulating the surface, you can increase the critical heat flux by 10 to 20%, then you increase the power produced by the same amount, on a global scale, by making better use of the fuel and resources that are already there,” Bucci said.

Massachusetts Institute of Technology (MIT)

www.mit.edu

– Edited by Chris Vavra, production editor, Control Engineering, CFE Media, cvavra@cfemedia.com. See more Control Engineering energy and power stories.


David L. Chandler
Author Bio: MIT News Office