Comparative modulation: Spread spectrum modulation terms and definitions for wireless networking

Industrial wireless tutorials: Modulation is, simply put, a mixing of the carrier wave with the data to be transmitted; analog or digital signals are combined with a carrier producing a hybrid signal, which is then demodulated at the receiver. This is the underlying theory behind all modulation-demodulation schemes. See the terms and definitions for related wireless networking acronyms.

07/08/2014


Industrial Wireless Tutorials – a new Control Engineering blogWe touched briefly on modulation in the last wireless tutorial blog on radio frequency (RF). Modulation is, simply put, a mixing of the carrier wave with the data to be transmitted; analog or digital signals are combined with a carrier producing a hybrid signal, which is then demodulated at the receiver. This is the underlying theory behind all modulation-demodulation schemes. Below see the terms and definitions for wireless networking acronyms you may have seen: FHSS, DSSS, OFDM, FSK, PSK, and QAM.

Until recently, the predominant form of Wi-Fi modulation was the method known as spread spectrum. This technology breaks data into smaller pieces, called "chips," and spreads these chips over multiple subcarriers. This method allows for a much more reliable and interference resistant transmission. Spread spectrum has the advantages of low power density and redundancy. Low power density results from the signal being spread over a wide band, allowing for less power per individual subcarrier, and redundancy refers to the fact that data is spread over several subcarriers and can be recovered in case of error. This also makes the signal more robust and resistant to interference and interception. 

Characteristics of spread spectrum modulation

Spread spectrum modulation has the following characteristics:

  • The bandwidth of the transmitted signal is greater than that of the original data.
  • The bandwidth of the transmitted signal is determined by the data transmitted and the spreading code.

Related terms, acronyms, and definitions for spread spectrum modulation follow.

- Frequency hopping spread spectrum (FHSS) is a form of spread spectrum that has been in use for more than 70 years. Bluetooth uses FHSS; data is spread over 40 subcarriers of 1 MHz each. FHSS is very resistant to narrowband interference and FHSS transmissions are very difficult to intercept. However, data rates top out at about 3 MBPS.

- Direct sequence spread spectrum (DSSS) uses an algorithm that modulates every bit with a sequence of 11 bits called "chips." The process is known as "chipping" and follows a spreading code, typically the Barker Code, to chip data into pseudonoise (PN) symbols. The transmitted signal sounds very much like static.

- Orthogonal frequency division multiplexing (OFDM) uses 52 orthogonally sequenced subcarriers (56 in IEEE 802.11n) to transmit data. While not technically a spread spectrum technology, it is included here because it is a dominant form of modulation in Wi-Fi. Orthogonal means "at right angles"; the center frequency of each subcarrier is 90 deg out of phase with adjoining carrier center frequencies, eliminating crosstalk or interference.

- Frequency shift keying (FSK) is a very old technology dating back to telegraphy. FSK is simply a shifting of frequency between two different frequencies to represent a one or a zero (mark and space). Similarly, phase shift keying (PSK) uses a shift in phase angle to represent a symbol or change in state.

- Quadrature amplitude modulation (QAM) uses a phase map that produces coordinates defined by the amplitude and phase angle of a signal. The phase map has four quadrants, corresponding to the four angular parts of a sine wave. In the most basic form, four symbols can be represented. Common iterations are 8, 16, 32, 64, 128, and 256-QAM. Each number represents the number of symbols capable of being encoded per cycle. As you can see, very high spectrum efficiency can be achieved with the appropriate modulation.

- Daniel E. Capano, owner and president, Diversified Technical Services Inc. of Stamford, Conn., is a certified wireless network administrator (CWNA). Edited by Mark T. Hoske, content manager, CFE Media, Control Engineering, mhoske@cfemedia.com.

ONLINE extras

www.controleng.com/blogs has other wireless tutorials from Capano.

www.controleng.com/webcasts has wireless webcasts, some for PDH credit.

Control Engineering has a wireless page



Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
October 2018
HMI hardware evolution, Data acquisition strategies, Matching motors and drives, Machine vision advice
September 2018
Optimize controls via cloud software, ladder logic simulation, industrial wireless best practices
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
October 2018
HMI hardware evolution, Data acquisition strategies, Matching motors and drives, Machine vision advice
September 2018
Optimize controls via cloud software, ladder logic simulation, industrial wireless best practices
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
October 2018
HMI hardware evolution, Data acquisition strategies, Matching motors and drives, Machine vision advice
September 2018
Optimize controls via cloud software, ladder logic simulation, industrial wireless best practices
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me