Controller for crane testing

Inside Machines, hydraulic control: Verifying load parameters when testing mobile cranes is important to verify quality, which matters for functionality and safety. New testing systems included installing new proportional servo valves and high-performance, electro-hydraulic motion controllers.

12/04/2016


Figure 1: The new Ihber test system simulates either fixed-flow or variable-flow hydraulic pumps for crane operation. Shown are the control and hydraulic panels for one test stand. Courtesy: Delta Motion SystemsHiab, an operating unit of Cargotec of Helsinki, Finland, is the world´s leading provider of on-road load handling equipment. The company undergoes a rigorous protocol for testing its mobile hydraulic crane products to ensure that they meet design specifications. Testing protocols involve driving the cranes, while monitoring crane operation to verify performance. A wide range of hydraulic fluid flows are required, varying from 10 lpm to 150 lpm. If the flow is not precisely regulated, in particular at low fluid flows, the ability of the company's cranes to make very precise lifting motions cannot be verified. 

Testing system upgrade

Hiab's old test system consisted of a main 270 kW hydraulic power unit (HPU) that feeds six test stands at 350 bar (5,000 psi) continuous pressure. Each stand can simulate either a fixed flow or a variable flow pump. Each test stand used a programmable logic controller (PLC) providing closed-loop control via a standard performance proportional valve and a pressure compensator to maintain the desired flow.

The test system worked, but Hiab's quality control people were dissatisfied with test quality in some operating modes. In particular, the system was very sensitive to the performance of the pressure compensator device, which had difficulty regulating the target differential pressures at very small fluid flows or at high-load induced pressures. The need to perform frequent calibrations of the compensators to adjust for weakening internal springs had also become a maintenance headache. In seeking a solution, the Hiab people contacted Ihber of Zaragoza, Spain, a hydraulic company specializing in advanced customized applications, such as motion control and testing.

Hiab wanted improved test stands to "cover the complete flow range and dramatically reduce maintenance tasks," said Javier Berné, Ihber technical manager. In turn, the Ihber team proposed the installation of new proportional servo valves and high-performance, electro-hydraulic motion controllers. "Avoiding the pressure compensator means less maintenance, and use of the high performance valve and controller means better performance," continued Berné.

Figure 2: A black crane is visible in the background while testing is in process. Courtesy: Delta Motion SystemsTwo weeks during summer holidays were available to disassemble existing test stands, install the new systems (one stand is shown in Figure 1), and test and tune the controls (see Figure 2).

"Perfect performance from the first day was a must," said Berné. "We chose to use particular two-axis controllers because of their performance, the capabilities of the software that is supplied for free with the controllers, and the high level of technical support that the vendor provided was impressive."

Each motion controller (shown in Figure 3 as mounted in one test stand's control panel) was programmed to simulate the performance of hydraulic pumps in two operating modes. Each mode employs a different sensor configuration. A programming feature called custom feedback allows the controller to easily switch between modes. 

Programming advantages

The first mode simulates feeding with a fixed flow pump and a pressure-limiting valve. In this mode, the motion controller is interfaced to a servo valve, a flowmeter, and a pressure sensor. The controller is programmed using a velocity control loop with force limiting feature. In this mode, the controller runs the velocity and force proportional-integral-derivative (PID) algorithms in parallel and uses the minimum of two PID control signals to drive the actuator. In the Hiab testing application, Ihber's engineers programmed the velocity loop to control hydraulic fluid flow to the crane, while the force loop is set to limit the applied pressure.

Figure 3: Inside the control panel: Each test stand is controlled via a PLC (center left) and a Delta Computer Systems RMC75P motion controller (center right). The PLC and motion controller are connected via Profibus (the purple cable).The second operating mode of the test system simulates a variable flow pump with load sensing and a cut-off compensator. Again, force limiting was employed in programming the controllers, with the first loop controlling differential pressure across the crane valve (using two pressure sensors, one for crane supply and another for load-sensing) and pressure limiting by the second loop.

"The use of the motion controller's force-limiting capability allowed us to avoid transitioning between separate control modes for velocity or differential pressure and pressure regulation during system operation," said Berné. "This makes for smoother operation and minimizes test system maintenance issues." 

Motion-control loop tuning

Besides supporting the programming of motion functions, the development tool software provides support for tuning motion-control loops for precise operation.

"Real-time plotting of all the motion parameters using the plot manager allowed us to very quickly understand the system and find a good and smooth response in every situation, even after an emergency stop or during the first movements, when there is entrapped air in the crane circuit," said Berné.

In addition to the motion controller, each test stand has a PLC and a touch screen human-machine interface (HMI). All elements communicate over Profibus and connect via Profibus to an additional PLC that controls the HPU and manages alarms. Using the touch screen, the user can specify the control type (fixed or variable flow), target parameters (such as flow, maximum pressure, differential pressure), and other information the controller needs. The touch screen also receives information from the controller, including actual parameter values measured during system operation.

"With the new controls in place, the performance of the system is much better than our customer expected," said Berné. "Thanks to valve and controller performance, flow control is very accurate, even with small flows, and pressure limiting works fine for light and heavy crane loads and different speeds."

Richard Meyerhoefer is regional applications specialist at Delta Computer Systems Inc.; Edited by Mark T. Hoske, content manager, CFE Media, Control Engineering, mhoske@cfemedia.com.

MORE ADVICE

Key concepts

Upgrades of motion control test stands were needed to improve quality and decrease maintenance.

New controllers increased capabilities.

Related software added functionality.

Consider this

Can a new controller upgrade add capabilities making it worth the investment, even if existing controllers still work?

ONLINE extra

Delta Motion Systems has more information about related technologies. www.deltamotion.com 

See additional information and link to the Control Engineering motion control page.



Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
July 2018
Ladder logic best practices and object-oriented programming, safety instrumented systems, enclosure design issues and challenges, process control advice
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
July 2018
Ladder logic best practices and object-oriented programming, safety instrumented systems, enclosure design issues and challenges, process control advice
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
July 2018
Ladder logic best practices and object-oriented programming, safety instrumented systems, enclosure design issues and challenges, process control advice
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me