Fixing PID, Part 2

Proportional-integral-derivative controllers may be ubiquitous, but they’re not perfect.

04/28/2014


Part 1 of this series (Control Engineering, Nov. 2012) looked at several issues that limit the performance of the theoretical PID algorithm in real-world applications of feedback control.

All of these problems are exacerbated by uncertainty. Sometimes the controller lacks sufficient information about the controlled process to know how much and how long to apply a control effort. Sometimes the controller can't even tell if it's done a good job or how to do a better job in the future when sensor placement, physical limitations of the sensing technology, or measurement noise make the process variable hard to measure.

Measurement noise is particularly troublesome for a PID controller's derivative action. To compute the "D" component of its next control effort, the controller computes the latest change in the error (the difference between the process variable and the setpoint) and multiplies that by the derivative gain or rate parameter.

When random electrical interference or other glitches in the sensor's output cause the controller to see fictitious changes in the process variable, the controller's derivative action increases or decreases unnecessarily. If the noise is particularly severe or the derivative gain is particularly high, the controller's subsequent chaotic control efforts may be not only unnecessary, but also damaging to the actuator and perhaps even to the controlled process itself.

Filtering

The simplest solution to this problem is to reduce the derivative gain when measurement noise is high, but doing so limits its effectiveness. The measurement noise itself can sometimes be reduced by fixing the sensor or by filtering the process variable measurement mathematically. A process variable filter essentially averages the sensor's most recent outputs to produce a better estimate of the process variable's actual value.

However, process variable filters have their limitations. They only work if the measurement noise is truly random, sometimes increasing and sometimes decreasing the sensor's output in equal measure. If those positive and negative blips also occur with equal frequency, then the filter's averaging operation will tend to cancel them out. But if the measurement noise tends to skew the sensor's output consistently in one direction or the other, the filtered process variable will tend to run consistently too high or too low, thereby deceiving the controller into working too hard or too little.

A process variable filter also slows the controller's reaction time. If the filter is configured to average a particularly long sequence of sensor outputs, it will do a better job of cancelling out random blips, but it will also tend to miss the most recent changes in the actual process variable. The filter needs to see a sustained change in the sensor's output before it can report a new value of the process variable to the controller. The controller can't even see, let alone react to rapid, short-term changes in the process variable, as discussed in the "Filtering" section below.

As a compromise, some PID controllers can be configured to filter the process variable to differing degrees when computing the proportional, integral, and derivative actions. The derivative action requires the most filtering since that's where measurement noise causes the most problems. The proportional action may benefit from less filtering (that is, a filter incorporating a shorter sequence of sensor outputs) in order to remain responsive to short-term changes in the process variable. And since the integral action itself serves as a filter, it may require no process variable filtering at all.

Alternately, a filter can be applied to the control effort instead of the process variable. Doing so permits the measurement noise to enter into the PID calculations (especially the "D"), but the noisy control effort that results is smoothed by the filter before reaching the actuator. A filter can also help slow down the control effort to prevent overly dramatic fluctuations in the process's behavior in cases where the process is particularly sensitive to the actuator's movements.

On the other hand, a filter on the control effort can make the process appear more sluggish than it really is. An operator looking for faster closed-loop performance might try re-tuning the controller to be more aggressive without realizing that the problem is the damping effect of the filter, not the process. The controller tuning and the control effort filter sometimes end up battling each other unnecessarily when different operators have implemented one without checking for the other.

Deadband

The effects of measurement noise can also be mitigated by simply ignoring insignificant changes in the sensor's output under the assumption that they're probably just artifacts of the measurement noise and are too small to make a difference in the controller's choice of control efforts anyway. So long as the error between the process variable and the setpoint remains within a range known as the deadband, the controller simply does nothing.

The trick is determining how much of a change in the error is small enough to ignore. If the deadband is set too large, significant changes in the behavior of the process may be overlooked. But if it is set too small, the controller will react unnecessarily to every fictitious blip in the sensor's output, even if the actual process variable has already reached the setpoint.

Unfortunately, a deadband also glosses over small changes in the setpoint. If an operator tries to move the process into a higher or lower operating range that falls within the current deadband, the resulting change in the error will be ignored and the controller will do nothing. If the deadband is too large, the controller's precision will suffer. That is, it may be able to make a refrigerated space five degrees colder, but not just one.


<< First < Previous Page 1 Page 2 Next > Last >>

Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
October 2018
HMI hardware evolution, Data acquisition strategies, Matching motors and drives, Machine vision advice
September 2018
Optimize controls via cloud software, ladder logic simulation, industrial wireless best practices
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
October 2018
HMI hardware evolution, Data acquisition strategies, Matching motors and drives, Machine vision advice
September 2018
Optimize controls via cloud software, ladder logic simulation, industrial wireless best practices
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
Design of Safe and Reliable Hydraulic Systems for Subsea Applications
This eGuide explains how the operation of hydraulic systems for subsea applications requires the user to consider additional aspects because of the unique conditions that apply to the setting
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
October 2018
HMI hardware evolution, Data acquisition strategies, Matching motors and drives, Machine vision advice
September 2018
Optimize controls via cloud software, ladder logic simulation, industrial wireless best practices
August 2018
Augmented reality and virtual reality education, autotuning PID control, cybersecurity advice, educating engineers
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

October 2018
2018 Product of the Year; Subsurface data methodologies; Digital twins; Well lifecycle data
August 2018
SCADA standardization, capital expenditures, data-driven drilling and execution
June 2018
Machine learning, produced water benefits, progressive cavity pumps
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me