Six tips for testing motor insulation systems

Insulation resistance (IR) tests are useful for motor insulation systems and users should take steps such as recording conditions and watching for factors that may have an impact on the test to ensure maximum accuracy.

05/03/2017


Although there are many ways to assess motor insulation systems, the insulation resistance (IR) test remains a useful tool for determining if a motor should be removed from or placed into service. When conducting the test and evaluating the results, consider these six tips.

Table 1: Guidelines for dc voltages to be applied during insulation resistance tests. Courtesy: EASA, IEEE

1. Discharge for safety and accuracy. Discharge the winding to ground before and after IR testing. A good rule of thumb is to ground the winding for 15 minutes or four times the test time, whichever is greater.

2. Winding configuration for testing. If possible, isolate and test each phase separately and ground the two phases not under test. This allows for testing of the phase-to-phase insulation as well as the ground insulation.

3. Record important test conditions. Document the ambient temperature, relative humidity, dew point, winding temperature, time since service, test voltage and connection arrangement.

4. Simple test procedure. Energize the winding for one minute at an appropriate voltage (see Table 1) and correct the measured IR value to 40°C by multiplying by a KT from Table 2. Most modern insulation falls under the "Thermosetting" category. Use the "Thermoplastic" values if you know it is a much older winding with an asphaltic or shellac mica system.

Table 2: Kt versus temperature for thermoplastic and thermosetting insulation stator winding systems. Courtesy: EASA, IEEE

5. Watch for factors that can affect the IR test. During the test, watch out for these four factors that can have an impact on the test and its results:

  • Surface contamination such as oil, dust and salts may be conductive, causing lower IR. Cleaning and drying the winding will usually improve the IR.
  • If the winding temperature is at or below the dew point, moisture may accumulate on the surface, causing low IR values. When the winding is otherwise in good condition, drying will resolve this issue.
  • Winding IR decreases when winding temperature increases, which is why correction to a baseline temperature is recommended.
  • Voltage magnitude and existing charge also can affect IR, but selecting the voltage from Table 1 and following proper grounding practices before testing should eliminate this issue.

Table 3: Recommended minimum insulation resistance values at 40 °C (all values in MΩ). Courtesy: EASA, IEEE

6. Evaluate the test results. Table 3 shows the recommended values for the corrected IR. Lower values warrant further investigation before the unit is placed into service. Some machines do operate below these values. Having historical data on-hand is valuable.

Mike Howell is a technical support specialist at the Electrical Apparatus Service Association (EASA), a CFE Media content partner. Edited by Chris Vavra, production editor, Control Engineering, CFE Media, cvavra@cfemedia.com.

MORE ADVICE

Key Concepts

  • Insulation resistance (IR) tests are useful for determining whether a motor should be removed.
  • During the test, the user should discharge for safety and accuracy and record important test conditions.
  • Users should also be aware of factors that might affect the IR test.

Consider this

What other aspects should users watch for while performing an IR test on a motor?



Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
July 2018
Ladder logic best practices and object-oriented programming, safety instrumented systems, enclosure design issues and challenges, process control advice
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
May 2018
Salary and Career Survey, IT and OT convergence, robotic standards and safety, secure circuit protection
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
February 2018
Focus on power systems, process safety, electrical and power systems, edge computing in the oil & gas industry
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
July 2018
Ladder logic best practices and object-oriented programming, safety instrumented systems, enclosure design issues and challenges, process control advice
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
May 2018
Salary and Career Survey, IT and OT convergence, robotic standards and safety, secure circuit protection
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
February 2018
Focus on power systems, process safety, electrical and power systems, edge computing in the oil & gas industry
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
July 2018
Ladder logic best practices and object-oriented programming, safety instrumented systems, enclosure design issues and challenges, process control advice
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
May 2018
Salary and Career Survey, IT and OT convergence, robotic standards and safety, secure circuit protection
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
Data Center Design
Data centers, data closets, edge and cloud computing, co-location facilities, and similar topics are among the fastest-changing in the industry.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
February 2018
Focus on power systems, process safety, electrical and power systems, edge computing in the oil & gas industry
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me