Tips on sizing pneumatic actuators

Pneumatic actuators come in many design types, but all share the same need for basic understanding of how their torque operates a valve. Understanding torque requirements and how to size an actuator are crucial.

01/28/2017


Pneumatic actuators come in many design types, but all share the same need for basic understanding of how their torque operates a valve. Accuracy is critical regardless of who sizes it. Incorrectly sizing an actuator can lead to a multitude of problems. Sometimes an actuator will have enough torque to open a valve but not enough to close it. Sometimes a valve may get stuck in mid-stroke. Other times, an actuator may provide so much torque that it damages the stem of the valve which it is operating.

When sizing an actuator, first consider the valve's torque requirements. Users need to consider:

  • Break torque
  • Running torque
  • Closing torque
  • Maximum shaft torque. 

Different valve types have different torque signatures. For example, a metal seated butterfly valve requires a large amount of torque to break or close and very little torque while traveling between the two positions. A metal seated ball valve requires a large amount of torque to open or close but also has an elevated torque requirement while traveling.

Some basic valve definitions users need to know are:

  • Break torque, also known as opening torque. This is the amount of torque required to start the movement of a valve from the closed position.
  • Running torque, also known as mid-stroke torque. This is the amount of torque required to maintain movement of the valve between open and closed positions.Seating Torque, also known as closing torque. This is the amount of torque required to seat a valve into its closed position.
  • Maximum allowable stem torque (MAST), which is the torque required to permanently deform or break the valve stem.
  • Safety factor is a given multiple of the valve's operating torques to ensure proper operation of the actuator. Many customers ask for a 25% safety factor so if a valve requires 100 in-lb torque to open, the actuator's break torque would be sized at 125 in-lbs.
  • Modulating service, also known as throttling service. A valve that is used as a control valve may have its position continuously increasing, decreasing, or stopping movement through its mid-stroke in order to control the valve's output. Modulating valves are rarely fully open or fully closed. Modulating valves usually require more torque than simple on-off valves.
  • On-off service is for a valve that is used for shut-off. It will either be used fully closed or fully open and will not stop during mid-stroke.

Pneumatic actuators come in many design types, but all share the same need for basic understanding of how their torque operates a valve. Understanding torque requirements and how to size an actuator are crucial. Courtesy: Cross CompanySize an actuator correctly by understanding torque

Before sizing an actuator, check with the valve manufacturer for their valve's torque requirements in your service.

Most manufacturers will publish a minimum torque required at a given operating pressure to open the valve in water service. In most instances, closing torque is the same as opening torque. Others will only publish the torque required at maximum operating conditions. Rarely do valve manufacturers publish the running torque of their valve. In any case, you may not have enough information to properly size an actuator even with the published torques based on what type of actuator you chose. Be very careful to also consider what media is flowing through the valve. Some services will increase the torque required to operate a valve. Also, consider if your customer requires you to add a safety factor to the valve torque prior to sizing an actuator.

Actuator design will affect the sizing. Rack and pinion actuators produce a constant torque output throughout the stroke. Scotch yoke actuators produce reduced torque in its mid-stroke. Please look at the manufacturer's published torque outputs and make sure you are aware of the torque signature of the actuator.

A spring return actuator has reduced torque the further it is operated because it is overcoming internal springs that are used to return the actuator to its initial position once air is removed. Users will need to know your customer's real air supply available at the valve in order to properly size an actuator. Just because their compressor is set at a certain pressure does not mean they have the same pressure at the valve

Some basic actuator definitions users need to know are:

  • Single acting: also knows as fail open or fail closed. It is an actuator with internal spring that will return the valve to the initial position on loss of air supply. 
  • Double acting: Air is required to open or close the actuator. The actuator will fail in place with the loss of air supply. Also known as Direct Acting.Start of AirThe amount of torque produced by the air supply to the actuator to start a movement from the normal position.
  • End of spring is the amount of torque that the internal springs provide in the normal position with all air pressure removed. In this position, the spring is considered to be in its relaxed position (with a pre-load).
  • Minimum air: It is the lowest torque valve of the actuator produced by the air supply. Depending on actuator type, this may be the same value as end of air. Other times it may be the mid-stroke position. Please refer to actuator's manufacturer.
  • End of air is the amount of torque produced by the air to hold the actuator at its end of travel position.
  • Start of spring is the amount of torque produced by the internal spring at the actuator's end of stroke position. This is the force the actuator will supply as the air is removed and the actuator reverses directions from its end of travel position.

Ronnie Moore is Cross Company's resident valve expert working in inside sales and support. A Knoxville native, Ronnie spent time in the Air Force as crew chief during the first Gulf War. This article originally appeared on Cross Company's Instrumentation blog. Edited by Chris Vavra, production editor, Control Engineering, CFE Media, cvavra@cfemedia.com.



Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
May 2018
Salary and Career Survey, IT and OT convergence, robotic standards and safety, secure circuit protection
April 2018
Cybersecurity best practices, artificial intelligence, robotic additive manufacturing, embedded systems, IIoT integration, energy efficiency
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
February 2018
Focus on power systems, process safety, electrical and power systems, edge computing in the oil & gas industry
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
May 2018
Salary and Career Survey, IT and OT convergence, robotic standards and safety, secure circuit protection
April 2018
Cybersecurity best practices, artificial intelligence, robotic additive manufacturing, embedded systems, IIoT integration, energy efficiency
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
February 2018
Focus on power systems, process safety, electrical and power systems, edge computing in the oil & gas industry
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
Engineers' Choice Awards
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers.
System Integrator Giants
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
System Integrator of the Year
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
How to Maximize Factory Automation Efficiency with Low Cost Machine Vision
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Wireless Reliability in Harsh Environments
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
Human Factors and the Impact on Plant Safety
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
June 2018
Discrete and process sensor fundamentals, autotuning controls, system integrator roundtable
May 2018
Salary and Career Survey, IT and OT convergence, robotic standards and safety, secure circuit protection
April 2018
Cybersecurity best practices, artificial intelligence, robotic additive manufacturing, embedded systems, IIoT integration, energy efficiency
Edge Computing
This article collection contains several articles on how today's technologies heap benefits onto an edge-computing architecture such as faster computing, better networking, more memory, smarter analytics, cloud-based intelligence, and lower costs.
IIoT: Machines, Equipment, & Asset Management
Articles in this digital report highlight technologies that enable Industrial Internet of Things, IIoT-related products and strategies.
PLCs
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. Featured articles in this digital report compare PLCs and programmable automation controllers (PACs), industrial PCs, and robotic controllers.
SIDB

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

June 2018
Machine learning, produced water benefits, progressive cavity pumps
April 2018
ROVs, rigs, and the real time; wellsite valve manifolds; AI on a chip; analytics use for pipelines
February 2018
Focus on power systems, process safety, electrical and power systems, edge computing in the oil & gas industry
John O. Ayuk, PE, CFSE, PMP, CAP
Automation Engineer; Wood Group
Doug Baker
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
Data Centers: Impacts of Climate and Cooling Technology
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
Safety First: Arc Flash 101
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
Critical Power: Hospital Electrical Systems
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me