Understanding modulation and coding schemes

Industrial Wireless Tutorials: Modulation and coding schemes (MCS) are used to determine the data rate of a wireless connection using high-throughput orthogonal frequency division multiplexing (HT-OFDM).

12/19/2014


Industrial Wireless Tutorials – a new Control Engineering blogBeginning with the introduction of IEEE 802.11n, modulation and coding schemes (MCS) are used to determine the data rate of a wireless connection using high-throughput orthogonal frequency division multiplexing (HT-OFDM). Pre-802.11n systems using OFDM had defined data rates between 6 and 54 Mbps based on what type of modulation and coding were used. HT-OFDM uses other parameters, such as channel size, number of spatial streams, coding method, modulation technique, and guard interval. Each MCS is based on a combination of these parameters. There are 77 different types of MCS for both 20 and 40 MHz channels, eight of which are mandatory for 20 MHz channels, and correspond to mandatory basic data rates.

The concept of multiple spatial streams was covered in a previous segment. A new concept is that of the guard interval (GI). When data is encoded by any of the various methods described, bits are converted to symbols, which are then modulated onto the carrier signal for transmission. In a legacy OFDM system, a symbol contains 288 bits, of which 216 are data and 72 are used for error correction. A typical symbol has a duration of 4 µs. To avoid the problem of intersymbol interference (ISI), a guard interval of 800 nanoseconds is inserted into each symbol (the symbol is actually 3.2 µs, the GI is .8µs). ISI occurs because of the multipath phenomenon; symbols that reach the receiver at different times, called the delay spread, can interfere with and corrupt one another, resulting in frequent retransmissions. Maximum delay spread is typically about 200 nanoseconds, so the guard interval is set at four times the maximum.

802.11n HT-OFDM systems also use an 800 nanosecond GI, but there is an option to use a 400 nanosecond GI. Using a smaller GI will increase throughput, but could also compromise system reliability. A shorter GI corresponds to a shorter symbol time and ISI can occur. In solid, well-planned wireless systems, the shorter GI will work fine and an increase in throughput will be achieved; however, if the radio frequency (RF) environment is poor, use of the shorter GI will adversely affect system throughput and reliability.

802.11n systems determine the proper MCS to use based on channel conditions as discerned from feedback from the receiver. The MCS is negotiated during communication and serves to strike a balance between maximum possible data rate and maximum acceptable error rate. Figure 1 provides a sample of modulation and coding schemes for 802.11n HT-OFDM:

A chart of modulation and coding schemes for 802.11n HT-OFDM. Courtesy: Daniel E. Capano, Diversified Technical Services

As you can see, there is about a 10% increase in throughput using the shorter guard interval. Note the increase in throughput as more spatial streams are brought into play.

Daniel E. Capano, owner and president, Diversified Technical Services Inc. of Stamford, Conn., is a certified wireless network administrator (CWNA) and writes posts for the Control Engineering blog, Industrial Wireless Tutorials.A word about coding, or information rate: Recall our previous discussion about convolutional coding. In communication theory, convolutional coding is used as a forward error correcting code. Given the ratio k/n as the code rate, the code generates a total of n bits to every k bits of useful information, which results in n-k bits being redundant. For a convolutional code of 1/2, 3/4, or 5/6, one redundant bit is inserted after each single, third, or fifth bit, respectively; the data is then decoded at the receiving end by a specialized algorithm. The purpose of this operation is to introduce redundancy, increase the reliability of the information, and avoid retransmissions by correcting the errors, if any, at the receiving end. A full discussion of this technique is well beyond this tutorial, but much deeper explanations can be found on the web.

- Daniel E. Capano, owner and president, Diversified Technical Services Inc. of Stamford, Conn., is a certified wireless network administrator (CWNA). He can be reached at dcapano@sbcglobal.net. Edited by Chris Vavra, production editor, CFE Media, Control Engineeringcvavra@cfemedia.com.

ONLINE extras

This blog also appears in the December 2014 print edition of Control Engineering.

 

 

The formal name for the standard is IEEE 802.11n-2009 - IEEE Standard for Information technology — Local and metropolitan area networks — Specific requirements — Part 11: Wireless LAN Medium Access Control (MAC)and Physical Layer (PHY) Specifications Amendment 5: Enhancements for Higher Throughput.

http://standards.ieee.org/findstds/standard/802.11n-2009.html 

http://standards.ieee.org/findstds/standard/802.11n-2009.html

 

www.controleng.com/blogs has other wireless tutorials from Capano on the following topics:

OFDM: Orthogonal frequency division multiplexing

MIMO and spatial multiplexing

Propagation revisited: Multipath

www.controleng.com/webcasts has wireless webcasts, some for PDH credit.

Control Engineering has a wireless page.  



The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers. Vote now (if qualified)!
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Maximize ROI with integrated control system approach; Microcontrollers vs. PLCs; Power quality; Accelerate and rewire IIoT; Traits for excellent engineers
HMI effectiveness; Distributed I/O; Engineers' Choice Award finalists; System Integrator advice; Inside Machines
Women in engineering; Engineering Leaders Under 40; PID benefits and drawbacks; Ladder logic; Cloud computing
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. As we know, PLCs aren’t the only option for making decisions in a control loop, but they are likely why you’re here.
This digital report explains how plant engineers and subject matter experts (SME) need support for time series data and its many challenges.
This article collection contains several articles on how advancements in vision system designs, computing power, algorithms, optics, and communications are making machine vision more cost effective than ever before.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Control room technology innovation; Practical approaches to corrosion protection; Pipeline regulator revises quality programs
Cloud, mobility, and remote operations; SCADA and contextual mobility; Custom UPS empowering a secure pipeline
Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers. Vote now (if qualified)!
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Maximize ROI with integrated control system approach; Microcontrollers vs. PLCs; Power quality; Accelerate and rewire IIoT; Traits for excellent engineers
HMI effectiveness; Distributed I/O; Engineers' Choice Award finalists; System Integrator advice; Inside Machines
Women in engineering; Engineering Leaders Under 40; PID benefits and drawbacks; Ladder logic; Cloud computing
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. As we know, PLCs aren’t the only option for making decisions in a control loop, but they are likely why you’re here.
This digital report explains how plant engineers and subject matter experts (SME) need support for time series data and its many challenges.
This article collection contains several articles on how advancements in vision system designs, computing power, algorithms, optics, and communications are making machine vision more cost effective than ever before.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Control room technology innovation; Practical approaches to corrosion protection; Pipeline regulator revises quality programs
Cloud, mobility, and remote operations; SCADA and contextual mobility; Custom UPS empowering a secure pipeline
Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by Control Engineering subscribers. Vote now (if qualified)!
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Maximize ROI with integrated control system approach; Microcontrollers vs. PLCs; Power quality; Accelerate and rewire IIoT; Traits for excellent engineers
HMI effectiveness; Distributed I/O; Engineers' Choice Award finalists; System Integrator advice; Inside Machines
Women in engineering; Engineering Leaders Under 40; PID benefits and drawbacks; Ladder logic; Cloud computing
Programmable logic controllers (PLCs) represent the logic (decision) part of the control loop of sense, decide, and actuate. As we know, PLCs aren’t the only option for making decisions in a control loop, but they are likely why you’re here.
This digital report explains how plant engineers and subject matter experts (SME) need support for time series data and its many challenges.
This article collection contains several articles on how advancements in vision system designs, computing power, algorithms, optics, and communications are making machine vision more cost effective than ever before.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Control room technology innovation; Practical approaches to corrosion protection; Pipeline regulator revises quality programs
Cloud, mobility, and remote operations; SCADA and contextual mobility; Custom UPS empowering a secure pipeline
Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me