Matrix drives reduce energy consumption for transporter system

Inside Machines: Industrial matrix drives were used for a transporter system retrofit to reduce energy consumption and costs by creating a more maintenance-free mechanically integral distribution system. New system regeneration capabilities for two motors saves an estimated $1,500 per year.


The 40HP U1000 direct ac to ac drive controls the two motor vessel axis. Courtesy: Yaskawa America Inc.A material handling application will be regenerating about $1,500 per year in electrical savings rather than dissipating braking energy as heat. Other savings are expected with a simpler design expected to require less maintenance. In spring 2016, Maxam Inc. and Yaskawa America Inc. developed an asphalt transporter system for Gallagher Asphalt in Thornton, Ill.

The transporter system is a fully integrated asphalt distribution product that is designed to load and evenly distribute asphalt into individual load out silos. The Gallagher Asphalt system's motor-driven transporter featured an eight-ton high-speed material transfer vessel and recharging storage vessel.

The old drag slat used chains, which required more power in conveyor plate heating than the retrofitted system. Courtesy: Yaskawa America Inc.The existing 200-ton asphalt storage silos were retrofitted with the asphalt transported system, replacing a complex system of asphalt material conveyors. Five 40 hp conveyor systems and their inefficient motors were removed and eliminated for the transporter system. The old drag slat-the steel floor in the conveyor-used chains, which required more power in conveyor plate heating than the retrofitted system.

The transporter system used two matrix drives. One drive operates the 60 hp, multi-motor powered carriage and another 30 hp drive operates the transfer vessel power train. The main carriage has four drive motors and the moving vessel (batcher) has two additional motors. The main carriage and the vessel need to be driven at exactly the same speed. The system is designed to be more energy efficient and provide a more maintenance-free, mechanically integral distribution system.

This transporter has been operating since February 2016. The duty cycle requires the motors ramp to full speed in about 1.5 seconds. They will run at speed for about 4 seconds, then ramp down in about 3.5 seconds to stop mode. In about 10 seconds, the system repeats the process. During the fast stop time, the transporter motor's regenerative load energy normally would be channeled into the ac drives' system braking resistors and dissipated as heat energy. Since the regenerative cycle would occur in about 20% of the total duty cycle time, significant amounts of energy would be lost as heat.

The asphalt system distributes asphalt to the six truck load out silos. Courtesy: Yaskawa America Inc.

The matrix ac drive works for this application because of its control technology. It employs a system of nine bi-directional switches arranged in a matrix to convert the three-phase ac input voltage directly into a three-phase ac output voltage. The ac drive topology eliminates the need for a rectifying circuit, dc smooth circuit, and the optional dynamic braking components usually required for this type of application.

The Maxam transporter asphalt mass transfer system is designed for silo loading and used two Yaskawa U1000 industrial matrix drives. Courtesy: Yaskawa America Inc.

The converter uses all three input phases in pulse width modulation (PWM) switching to control output voltage and input current, and it provides regenerative motor control operation. This control is required when the carriage and vessel motors decelerate. This allows the drive to save energy by regenerating the motor's overhauling energy directly back into Gallagher Asphalt's power distribution system. This is much more efficient than releasing the motor's regenerative energy as heat via a traditional ac drive's dynamic braking option.

The travelling batcher drive is designed for unloading the batch into each load out silo. Courtesy: Yaskawa America Inc.

The motor control centers (MCC) for the transporter systems are installed in outdoor-rated enclosures. Considerations for the limited MCC panel space, dirty, and wet weather environments along with wide ambient temperature fluctuations are important design criteria for this motor control solution. MCC wiring complexity is simple with the direct ac to ac matrix drive topology. Wiring requires little panel or field installation labor. The drive provides a three-phase power supply input and three-phase output main power supply wiring.

The main motor power circuit component count is reduced from several components to one. Using the drive selected allows control panels to be about 70% smaller than the traditional drive with dynamic brake module(s) and resistor(s) solution or a traditional ac drive regenerative power supply. Gallagher Asphalt applied for a Commonwealth Edison utility grant because of the energy savings offered by the matrix drive.

Gallagher's KWh costs are .076 cents/KWh. Operation cycle time is 8.5 hours per work day, five work days per week average with 40 weeks a year of operational time. Approximately 20% of the total run time is spent in regenerative mode. This is 340 hours/year. Assuming each motor is at 100% braking torque during regeneration, the 30 hp drive's total motor load will yield approximately $500/year and the 60 hp drive's total motor load will yield approximately $1,000/year of savings (based on $0.076/kwh) vs. the standard and typical solution of using a conventional ac drive solution with the dynamic braking resistor option.

Mike Grant is a regional drive specialist, Yaskawa America Inc. Edited by Chris Vavra, production editor, Control Engineering, CFE Media,


Key Concepts

  • Matrix drives were used for a transporter system retrofit for Gallagher Asphalt to reduce energy and maintenance costs.
  • The industrial matrix drives operated a multi-motor powered carriage and the transfer vessel power train.
  • The matrix drives reduced energy and maintenance costs for Gallagher Asphalt. 

Consider this

How could your motion control applications reduce the energy costs? 

ONLINE extra 

Four more photos appear with this article online, along with links to related information. For more information from Yaskawa about the drives mentioned, available for 5 hp to 800 hp, go here.

See additional photos below.

Batcher clam gate for controlling the specified asphalt volume (batch) that is discharged into the vessel. Courtesy: Yaskawa America Inc.The 60HP U1000 direct ac to ac drive controls the four-motor carriage axis. Courtesy: Yaskawa America Inc.

The system is designed to be more energy efficient and provide a more maintenance-free mechanically integral distribution. Courtesy: Yaskawa America Inc.Pneumatic cylinder controls for actuating the batching system gate, and material transfer sections. Courtesy: Yaskawa America Inc.

No comments
The Engineers' Choice Awards highlight some of the best new control, instrumentation and automation products as chosen by...
The System Integrator Giants program lists the top 100 system integrators among companies listed in CFE Media's Global System Integrator Database.
Each year, a panel of Control Engineering and Plant Engineering editors and industry expert judges select the System Integrator of the Year Award winners in three categories.
This eGuide illustrates solutions, applications and benefits of machine vision systems.
Learn how to increase device reliability in harsh environments and decrease unplanned system downtime.
This eGuide contains a series of articles and videos that considers theoretical and practical; immediate needs and a look into the future.
Controller programming; Safety networks; Enclosure design; Power quality; Safety integrity levels; Increasing process efficiency
Additive manufacturing benefits; HMI and sensor tips; System integrator advice; Innovations from the industry
Robotic safety, collaboration, standards; DCS migration tips; IT/OT convergence; 2017 Control Engineering Salary and Career Survey
Featured articles highlight technologies that enable the Industrial Internet of Things, IIoT-related products and strategies to get data more easily to the user.
This article collection contains several articles on how automation and controls are helping human-machine interface (HMI) hardware and software advance.
This digital report will explore several aspects of how IIoT will transform manufacturing in the coming years.

Find and connect with the most suitable service provider for your unique application. Start searching the Global System Integrator Database Now!

Infrastructure for natural gas expansion; Artificial lift methods; Disruptive technology and fugitive gas emissions
Mobility as the means to offshore innovation; Preventing another Deepwater Horizon; ROVs as subsea robots; SCADA and the radio spectrum
Future of oil and gas projects; Reservoir models; The importance of SCADA to oil and gas
Automation Engineer; Wood Group
System Integrator; Cross Integrated Systems Group
Jose S. Vasquez, Jr.
Fire & Life Safety Engineer; Technip USA Inc.
This course focuses on climate analysis, appropriateness of cooling system selection, and combining cooling systems.
This course will help identify and reveal electrical hazards and identify the solutions to implementing and maintaining a safe work environment.
This course explains how maintaining power and communication systems through emergency power-generation systems is critical.
click me